欢迎访问ic37.com |
会员登录 免费注册
发布采购

TDA9819T 参数 Datasheet PDF下载

TDA9819T图片预览
型号: TDA9819T
PDF下载: 下载PDF文件 查看货源
内容描述: 多标准视觉和声音中频锁相环与DVB- IF处理 [Multistandard vision and sound-IF PLL with DVB-IF processing]
分类和应用: 光电二极管
文件页数/大小: 40 页 / 270 K
品牌: NXP [ NXP ]
 浏览型号TDA9819T的Datasheet PDF文件第15页浏览型号TDA9819T的Datasheet PDF文件第16页浏览型号TDA9819T的Datasheet PDF文件第17页浏览型号TDA9819T的Datasheet PDF文件第18页浏览型号TDA9819T的Datasheet PDF文件第20页浏览型号TDA9819T的Datasheet PDF文件第21页浏览型号TDA9819T的Datasheet PDF文件第22页浏览型号TDA9819T的Datasheet PDF文件第23页  
Philips Semiconductors  
Product specification  
Multistandard vision and sound-IF PLL with  
DVB-IF processing  
TDA9819  
13. The intermodulation figures are defined:  
V0at 3.58 MHz  
α0.92 = 20 log  
+ 3.6dB ; α0.92 value at 0.92 MHz referenced to black/white signal;  
--------------------------------------  
V0at 0.92 MHz  
V0at 3.58 MHz  
α2.76 = 20 log  
; α2.76 value at 2.76 MHz referenced to colour carrier.  
--------------------------------------  
V0at 2.76 MHz  
14. Sound carrier ON; SIF SAW filter L9453; fvideo = 10 kHz to 10 MHz.  
15. Response speed valid for a VIF input level range of 200 µV up to 70 mV.  
16. To match the AFC output signal to different tuning systems a current source output is provided. The test circuit is  
given in Fig.7. The AFC-steepness can be changed by the resistors at pin 23.  
17. Depending on the ratio C/C0 of the LC resonant circuit of VCO (Q0 > 50; C0 = Cint + Cext; see Fig.12).  
18. The intercarrier mode can be activated by connecting the SIF input pins 31 and 32 to GND (only for negative  
modulation B/G and M standard). In this event the intercarrier level depends on the sound shelf of VIF SAW filter and  
the transmitter PC/SC ratio.  
19. Input level for second IF from an external generator with 50 source impedance. AC-coupled with 10 nF capacitor,  
fmod = 400 Hz, 25 kHz (50% FM deviation) of audio references. A VIF/SIF input signal is not permitted. Pins 8 and 28  
have to be connected to positive supply voltage for minimum IF gain. S/N and THD measurements are taken at 75 µs  
de-emphasis. The FM demodulator steepness Vo AF/fAF is negative.  
20. Measured with an FM deviation of 25 kHz the typical AF output signal is 500 mV RMS (Rx = 0 ; see Fig.12). By  
using Rx = 470 the AF output signal is attenuated by 6 dB (250 mV RMS). For handling an FM deviation of more  
than 53 kHz the AF output signal has to be reduced by using Rx in order to avoid clipping (THD < 1.5%). For an FM  
deviation up to 100 kHz an attenuation of 6 dB is recommended with Rx = 470 .  
21. The leakage current of the decoupling capacitor (2.2 µF) should not exceed 1 µA.  
22. For all S/N measurements the used vision IF modulator has to meet the following specifications:  
Incidental phase modulation for black-to-white jump less than 0.5 degrees;  
QSS AF performance, measured with the television-demodulator AMF2 (audio output, weighted S/N ratio) better  
than 60 dB (deviation 25 kHz) for 6 kHz sine wave black-to-white video modulation.  
23. The PC/SC ratio at pins 1 and 2 is calculated as the addition of TV transmitter PC/SC ratio and SAW filter PC/SC  
ratio. This PC/SC ratio is necessary to achieve the S/N(W) values as noted. A different PC/SC ratio will change these  
values.  
24. Measurements for M standard with SAW filter M3951M (Siemens) for vision IF (suppressed sound carrier) and  
M9352M (Siemens) for sound IF (suppressed picture carrier). Input level Vi SIF = 10 mV RMS, 25 kHz FM deviation.  
Measurements for B/G standard with SAW filter G3962 (Siemens) for vision IF (suppressed sound carrier) and  
G9350 (Siemens) for sound IF (suppressed picture carrier). Input level Vi SIF = 10 mV RMS, 27 kHz  
(54% FM deviation).  
25. Measurements taken with SAW filter L9453 (Siemens) for AM sound IF (suppressed picture carrier).  
1998 Jul 14  
19