欢迎访问ic37.com |
会员登录 免费注册
发布采购

TDA9819T 参数 Datasheet PDF下载

TDA9819T图片预览
型号: TDA9819T
PDF下载: 下载PDF文件 查看货源
内容描述: 多标准视觉和声音中频锁相环与DVB- IF处理 [Multistandard vision and sound-IF PLL with DVB-IF processing]
分类和应用: 光电二极管
文件页数/大小: 40 页 / 270 K
品牌: NXP [ NXP ]
 浏览型号TDA9819T的Datasheet PDF文件第14页浏览型号TDA9819T的Datasheet PDF文件第15页浏览型号TDA9819T的Datasheet PDF文件第16页浏览型号TDA9819T的Datasheet PDF文件第17页浏览型号TDA9819T的Datasheet PDF文件第19页浏览型号TDA9819T的Datasheet PDF文件第20页浏览型号TDA9819T的Datasheet PDF文件第21页浏览型号TDA9819T的Datasheet PDF文件第22页  
Philips Semiconductors  
Product specification  
Multistandard vision and sound-IF PLL with  
DVB-IF processing  
TDA9819  
SYMBOL  
PARAMETER  
CONDITIONS  
MIN.  
TYP.  
MAX.  
UNIT  
AFC circuit (DVB mode)  
SUS  
control steepness I23/f  
f0 = 48.75 MHz; see Fig.12 0.7  
and note 17  
0.98  
1.3  
µA/kHz  
µA/kHz  
SEU  
f0 = 43.0 MHz; see Fig.12  
and note 17  
0.45  
0.70  
0.95  
DVB output signal (IF input to DVB output)  
V18(p-p)  
output voltage  
CL < 15 pF; RL > 5 k; with 1.8  
2.1  
2.4  
V
(peak-to-peak value)  
internal AGC  
V18DC  
B
DC voltage  
2.5  
12  
17  
40  
V
1 dB bandwidth  
3 dB bandwidth  
CL < 15 pF; RL > 5 kΩ  
11  
MHz  
MHz  
dB  
αC(DVB)  
αH  
fundamental input signal and  
IF harmonics  
35  
suppression of in-band  
harmonics  
2.0 V (p-p) output voltage  
30  
35  
dB  
Notes to the characteristics  
1. Values of video and sound parameters are decreased at VP = 4.5 V.  
2. This parameter is not tested during production and is only given as application information for designing the television  
receiver.  
3. Source impedance: 2.3 kin parallel to 12 pF (SAW filter); fIF = 45 MHz.  
4. Loop filter 330 /220 nF; loop bandwidth for M standard: BL 70 kHz (natural frequency fn 12 kHz; damping factor  
d 2.9; loop bandwidth for B/G and L standard: BL 80 kHz (natural frequency fn 13 kHz; damping factor d 3.2;  
calculated with sync level within gain control range). Resonance circuit of VCO: Q0 > 50; Cext and Cint see Fig.12.  
5. Temperature coefficient of external LC-circuit is equal to zero.  
6. Vi IF = 10 mV RMS; f = 1 MHz (VCO frequency offset related to picture carrier frequency); white picture video  
modulation.  
7. Vi IF signal for nominal video signal.  
8. Offset current measured between pin 7 and half of supply voltage (VP = 2.5 V) under the following conditions:  
no input signal at VIF input (pins 1, 2, 4 and 5) and VIF amplifier gain at minimum (V28 = VP). Due to sample-and-hold  
mode of the FPLL in L standard, the leakage current of the loop filter capacitor (C = 220 nF) should not exceed  
500 nA.  
9. Measurements taken with SAW filter M3951M and M9352M (Siemens, M standard);  
frequency range = 10 kHz to 5 MHz. Sound carrier ON; PC/SC ratio 7 dB (transmitter); modulation VSB.  
10. The 7 dB buffer gain accounts for 1 dB loss in the sound trap. Buffer output signal is typical 2 V (p-p), in event of  
CVBS video amplifier output typical 1 V (p-p). If no sound trap is applied a 330 resistor must be connected from  
output to input (from pin 21 to pin 22).  
11. The leakage current of the AGC capacitor should not exceed 1 µA at M and B/G standard respectively 10 nA current  
at L standard. Larger currents will increase the tilt.  
12. S/N is the ratio of black-to-white amplitude to the black level noise voltage (RMS value, pin 10). B = 5 MHz weighted  
in accordance with “CCIR 567”.  
1998 Jul 14  
18