s
Electrical Characteristics (Ta=25˚C)
·
AN8009/AN8009M (9V Type)
Parameter
Output voltage
Line regulation
Load regulation
Symbol
V
O
REG
IN
REG
L
V
DIF (min.)
I
bias
RR
V
no
∆V
O
/Ta
T
j
=25˚C
Condition
V
I
=9.5 to 15V, T
j
=25˚C
I
O
=1 to 40mA, T
j
=25˚C
I
O
=1 to 50mA, T
j
=25˚C
V
I
=8.8V, I
O
=20mA, T
j
=25˚C
V
I
=8.8V, I
O
=50mA, T
j
=25˚C
I
O
=0mA, T
j
=25˚C
V
I
=10 to 12V, f=120Hz
f=10Hz to 100kHz
T
j
=–30 to+125˚C
min
8.64
typ
9
9
17
37
0.07
0.14
0.8
max
9.36
100
70
75
0.2
0.3
1.4
Unit
V
mV
mV
mV
V
V
mA
dB
µV
mV/˚C
Minimum I/O voltage difference
Bias current
Ripple rejection ratio
Output noise voltage
Output voltage temperature coefficient
47
59
150
0.45
Note1) The specified condition T
j
=25˚C means that the test should be conducted with each test time reduced (within 10ms) so that
the drift in characteristic value due to a temperature rise at chip junction can be ignored.
Note2) Unless otherwise specified, V
I
=10V, I
O
=20mA, C
O
=10µF
·
AN8010/AN8010M (10V Type)
Parameter
Output voltage
Line regulation
Load regulation
Minimum I/O voltage difference
Bias current
Ripple rejection ratio
Output noise voltage
Output voltage temperature coefficient
Symbol
V
O
REG
IN
REG
L
V
DIF (min.)
I
bias
RR
V
no
∆V
O
/Ta
T
j
=25˚C
V
I
=10.5 to 16V, T
j
=25˚C
I
O
=1 to 40mA, T
j
=25˚C
I
O
=1 to 50mA, T
j
=25˚C
V
I
=9.8V, I
O
=20mA, T
j
=25˚C
V
I
=9.8V, I
O
=50mA, T
j
=25˚C
I
O
=0mA, T
j
=25˚C
V
I
=11 to 13V, f=120Hz
f=10Hz to 100kHz
T
j
=–30 to+125˚C
46
Condition
min
9.6
typ
10
10
18
40
0.07
0.14
0.8
58
165
0.5
max
10.4
100
75
85
0.2
0.3
1.4
Unit
V
mV
mV
mV
V
V
mA
dB
µV
mV/˚C
Note1) The specified condition T
j
=25˚C means that the test should be conducted with each test time reduced (within 10ms) so that
the drift in characteristic value due to a temperature rise at chip junction can be ignored.
Note2) Unless otherwise specified, V
I
=11V, I
O
=20mA, C
O
=10µF
s
Application Circuit
V
in
V
out
AN8000
AN8000M
0.33µF
+
10µF
–
The AN8000/AN8000M series has IC internal gain increased in order to improve
performance. When the power line on the output side is long, use a capacitor of
10µF.
For the capacitor on the output side, attach it as close to the IC as possible.
When using at a low temperature, it is recommended to use the capacitors with
low internal impedance (for example, tantalum capacitor) for output capacitors.
PANASONIC [ PANASONIC SEMICONDUCTOR ]
