Philips Semiconductors
Product data
Low power dual operational amplifiers
NE/SA/SE532/
LM258/358/A/2904
DC ELECTRICAL CHARACTERISTICS
(continued)
T
amb
= 25
°C;
V+ = +5 V; unless otherwise specified.
SYMBOL
V
OS
V
OS
I
OS
I
OS
I
BIAS
S
I
B
V
C
CM
CMRR
V
O
OH
V
OL
I
CC
A
VOL
O
PSRR
PARAMETER
Offset voltage
1
Drift
Offset current
Drift
Input current
2
Drift
Common mode voltage range
3
Common-mode
Common-mode rejection ratio
Output voltage swing
Output voltage swing
Supply current
Large-signal
Large signal voltage gain
Supply voltage rejection ratio
Amplifier-to-amplifier coupling
4
Output current (Source)
I
OUT
Output current (Sink)
TEST CONDITIONS
R
S
= 0
Ω
R
S
= 0
Ω;
over temp.
R
S
= 0
Ω;
over temp.
I
IN(+)
– I
IN(–)
Over temp.
Over temp.
I
IN(+)
or I
IN(–)
I
IN(+)
or I
IN(–)
; Over temp.
Over temp.
V+ = 30 V
V+ = 30 V; Over temp.
V+ = 30 V
R
L
≥
2 kΩ; V+ = 30 V; over temp.
R
L
≥
10 kΩ; V+ = 30 V; over temp.
R
L
≥
10 kΩ; over temp.
R
L
=
∞,
V+ = 30 V
R
L
=
∞
on all amplifiers; V+ = 30 V; over temp.
R
L
≥
2 kΩ; V
OUT
±10
V
V+ = 15 V (for large V
O
swing); over temp.
R
S
= 0
Ω
f=1kHz to 20kHz (input referred)
V
IN+
= +1 V
DC
; V
IN–
= 0 V
DC
; V+ = 15 V
DC
V
IN+
= +1 V
DC
; V
IN–
= 0 V
DC
; V+ = 15 V
DC
;
over temp.
V
IN–
= +1 V
DC
,;V
IN+
= 0 V
DC
; V+ = 15 V
DC
V
IN–
= +1 V
DC
; V
IN+
= 0 V
DC
;V+ = 15 V
DC
;
over temp.
V
IN+
= 0 V; V
IN–
= +1 V
DC
; V
O
= 200 mV
I
SC
GBW
SR
V
NOISE
Short circuit current
5
Differential input voltage
6
Unity gain bandwidth
Slew rate
Input noise voltage
T
amb
= 25
°C
T
amb
= 25
°C
T
amb
= 25
°C;
f = 1 kHz
1
0.3
40
20
10
10
5
12
25
15
65
100
–120
40
20
20
8
50
40
60
V+
0
0
65
26
27
28
5
0.5
0.6
100
20
1.0
1.2
85
10
45
40
50
V+–1.5
V+–2.0
7
5
LM358A
Min
Typ
±2
Max
±3
±5
20
±30
±75
300
100
200
UNIT
mV
mV
µV/°C
nA
nA
pA/°C
nA
nA
pA/°C
V
V
dB
V
V
mV
mA
mA
V/mV
V/mV
dB
dB
mA
mA
mA
mA
µA
mA
V
MHz
V/µs
nV/√Hz
NOTES:
1. V
O
≈
1.4 V, R
S
= 0
Ω
with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ –1.5 V).
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of
the output so no loading change exists on the input lines.
3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 V without damage.
4. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance coupling increases at higher frequencies.
5. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately
40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 V
DC
, continuous short-circuits can exceed the
power dissipation ratings and cause eventual destruction.
6. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common-mode voltage range is V+ –1.5 V, but either or both inputs can go to +32 V
DC
without damage.
2002 Jul 12
5
PHILIPS [ NXP SEMICONDUCTORS ]
