N08L163WC2CZ1-55IL 参数 Datasheet PDF下载

N08L163WC2C

NanoAmp Solutions, Inc.

Advance Information

Absolute Maximum Ratings

Item

Voltage on any pin relative to V

SS

Voltage on V

CC

Supply Relative to V

SS

Power Dissipation

Storage Temperature

Operating Temperature

Soldering Temperature and Time

Symbol

V

IN,OUT

V

CC

P

D

T

STG

T

A

T

SOLDER

Rating

–0.3 to V

CC

+0.3

–0.3 to 4.5

500

–65 to 150

-40 to +85

260

o

C, 10sec

Unit

V

V

mW

o

C

o

C

o

C

Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional oper-

ation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied.

Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Operating Characteristics (Over Specified Temperature Range)

Item

Supply Voltage

Data Retention Voltage

Input High Voltage

Input Low Voltage

Output High Voltage

Output Low Voltage

Input Leakage Current

Output Leakage Current

Read/Write Operating Supply Current

@ 1

µs

Cycle Time

2

Read/Write Operating Supply Current

@ fmax

Maximum Standby Current

Symbol

V

CC

V

DR

V

IH

V

IL

V

OH

V

OL

I

LI

I

LO

I

CC1

I

CC2

Chip Disabled

Vcc = 2.2V to 2.7V

Vcc = 2.7V to 3.6V

Vcc = 2.2V to 2.7V

Vcc = 2.7V to 3.6V

I

OH

= -0.1mA, Vcc = 2.2V

I

OH

= -1.0mA, Vcc = 2.7V

I

OL

= 0.1mA, Vcc = 2.2V

I

OL

= 2.1mA, Vcc = 2.7V

V

IN

= 0 to V

CC

OE = V

IH

or Chip Disabled

V

CC

=3.6 V, V

IN

=V

IH

or V

IL

Chip Enabled, I

OUT

= 0

V

CC

=3.6 V, V

IN

=V

IH

or V

IL

Chip

Enabled, I

OUT

= 0

V

IN

= V

CC

or 0V

Chip Disabled

t

A

= 85

o

C, V

CC

= 3.6 V

-L

-L

-1

-1

1.5

1.5

12.0

12.0

2.0

-L

2.0

Test Conditions

Min.

2.2

1.5

1.8

2.2

–0.3

–0.3

2.0

2.4

0.4

0.4

1

1

3

3

20.0

15.0

20

8

10

4

µA

V

CC

+0.3

V

CC

+0.3

0.6

0.8

Typ

1

3.0

Max

3.6

Unit

V

V

V

V

V

V

µA

µA

mA

mA

I

SB1

Maximum Data Retention Current

I

DR

Vcc = 1.5V, CE

≥

Vcc - 0.2V,

VIN

≥

Vcc - 0.2V or VIN

≤

0.2V -L

µA

1. Typical values are measured at Vcc=Vcc Typ., T

A

=25°C and not 100% tested.

2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive

output capacitance expected in the actual system.

Stock No. 23380-C

The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.

3