• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance noCtice0. 2E.pdf
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
sales representatives or product engineers before ordering.
0. Please check with our sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
10.12.20
0. specifications before ordering.
LLL/LLR/LLA/LLM Series Specifications and Test Methods (2)
LLL/LLR/LLA/LLM Series Specifications and Test Methods (2)
When no "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (2).
No.
1
Item
Operating
Temperature
Range
Specifications
Test Method
R6: –55 to +85°C
R7, C7: –55 to +125°C
C8: –55 to +105°C
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
2
Rated Voltage
See the previous pages.
When AC voltage is superimposed on DC voltage, VP-P or VO-P
whichever is larger, should be maintained within the rated
voltage range.
,
3
4
Appearance
Dimensions
No defects or abnormalities
Visual inspection
Using calipers
Within the specified dimension
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
5
Dielectric Strength No defects or abnormalities
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at 25°C and 75%RH max. and
within 1 minute of charging.
Insulation
6
7
50Ω · F min.
Resistance
Capacitance
Within the specified tolerance
The capacitance/D.F. should be measured at 25°C at the
frequency and voltage shown in the table.
Capacitance
CV10µF (10V min.)
CV10µF (6.3V max.)
C>10µF
Frequency
1±0.1kHz
1±0.1kHz
120±24Hz
Voltage
Dissipation Factor
(D.F.)
1.0±0.2Vrms
0.5±0.1Vrms
0.5±0.1Vrms
8
R6, R7, C7, C8: 0.120 max.
The capacitance change should be measured after 5 min. at
each specified temperature stage.
Temp. Range
Reference
Temp.
The ranges of capacitance change compared with the 25°C
value over the temperature ranges shown in the table should
be within the specified ranges.
Char.
Cap. Change
(°C)
Capacitance
Temperature
Characteristics
R6
R7
C7
C8
–55 to +85
–55 to +125
–55 to +125
–55 to +105
Within ±15%
Within ±15%
Within ±22%
Within ±22%
9
25°C
• Initial measurement.
Perform a heat treatment at 150+0/-10°C for one hour and then
set for 24±2 hours at room temperature. Perform the initial
measurement.
Solder the capacitor to the test jig (glass epoxy board) using a
eutectic solder. Then apply 10N* force in parallel with the test
jig for 10±1 sec. The soldering should be done either with an
iron or using the reflow method and should be conducted with
care so that the soldering is uniform and free of defects such as
Adhesive Strength
of Termination
10
No removal of the terminations or other defect should occur.
heat shock.
*5N (LLL15, LLL18, LLR18, LLA, LLM Series)
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
Solder the capacitor to the test jig (glass epoxy board) in
the same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
11 Vibration
D.F.
R6, R7, C7, C8: 0.120 max.
perpendicular directions (total of 6 hours).
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2±0.5 seconds at 230±5°C, or
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.
Solderability of
Termination
75% of the terminations are to be soldered evenly
and continuously.
12
Appearance No marking defects
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270±5°C for 10±0.5 seconds.
Capacitance
Change
R6, R7, C7, C8: Within ±7.5%
Resistance
Let sit at room temperature for 24±2 hours, then measure.
13 to Soldering D.F.
R6, R7, C7, C8: 0.120 max.
Heat
• Initial measurement.
I.R.
50Ω · F min.
Perform a heat treatment at 150+0/–10°C for one hour and
then let sit for 24±2 hours at room temperature. Perform the
initial measurement.
Dielectric
Strength
No failure
Continued on the following page.
85
MURATA [ muRata ]
