ELECTRICAL SPECIFICATIONS
BBF2815S
BBF2815S H/E
Min.
Typ. Max.
BBF2815S
Group A
Subgroup
Units
Test Conditions 1
Parameter
Typ.
Max.
Min.
VDC
VDC
mA
mA
mVrms
mVrms
mArms
mArms
mV
mV
mV
mV
%
15.10
15.25
1
2,3
1
15.00 15.10 15.20 14.95
Output Voltage
-
-
14.80
-
-
15.40
1500
1400
50
-
-
1500
150
150
2
Output Current
16V≤VIN≤40V
-
-
2,3
1
150
-
-
25
60
-
25
-
-
BW=10KHz to 2MHz
BW=10KHz to 2MHz
VIN=16V to 40V
Output Voltage Ripple
Input Current Ripple 2
Line Regulation
-
-
2,3
1
-
60
-
20
40
-
20
-
40
-
-
-
2,3
1
-
50
-
10
60
-
10
50
-
-
-
2,3
1
-
-
125
50
-
20
60
-
20
-
-
IOUT=0.15A to 1.5A
Load Regulation
Efficiency
-
-
2,3
1
-
125
-
-
73
-
-
68
73
68
%
-
2,3
4
66
-
-
-
mV
mV
µS
IOUT=0.75A to/from 1.50A
Transition TIme=30µS
IOUT=0.75A to/from 1.50A
Transition TIme=30µS
VIN=16V to/from 40V
Transition Time=30µS
VIN=16V to/from 40V
Transition Time=30µS
800
1400
-
-
800
-
1200
1700
200
300
500
800
200
300
400
800
60
-
Step Load Response
Step Load Recovery
Step Line Response
Step Line Recovery
Start Up Overshoot
2
-
5,6
4
-
-
40
220
-
-
100
-
2
2
µS
-
5,6
4
-
-
-
mV
mV
µS
300
550
-
-
300
-
-
5,6
4
-
-
-
80
220
-
-
80
-
2
µS
-
5,6
4
-
-
-
mV
mV
mS
mS
µS
0
500
-
-
0
-
IOUT=1.5A
IOUT=1.5A
-
5,6
4
-
-
-
20
60
-
-
20
-
Start Up Delay
2
-
5,6
4
-
-
100
500
550
60
-
120
500
-
-
120
-
2
Shutdown Delay
µS
-
5,6
-
-
-
-
mS
V
2
2
30
60
40
40
-
Shutdown Recovery
Input Voltage Range
-
16
-
20
-
16
-
POUT=22.5W MAX.
Enabled, IOUT=0mA
-
1,2,3
1
-
40
mA
mA
mA
µF
35
35
40
Quiescent Current
-
2,3
1,2,3
1,2,3
1
-
-
50
-
Disabled IOUT=0mA
No Effect on DC Performance
1.25
2.5
300
-
-
1.25
2.5
300
-
-
2
Capacitive Load
Isolation
-
-
-
-
-
-
MΩ
A
Input to output or any pin to case @ 500V
100
1.5
475
10
100
1.5
475
10
7
Short Circuit Current Limit
Switching Frequency
2.4
500
-
3.0
525
-
1
2.4
500
-
3.0
525
-
KHz
%
4
VOUT Adjustment Range
RPOT=50KΩ
1
NOTES:
1 +VIN = 28V, IOUT = 1.5A, TA=TC=25°C unless otherwise specified.
2 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.
3 Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.
4 Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2, 3 and 4.
5 Subgroups 5 and 6 testing available upon request.
6 Subgroup 1, 4 TA=TC=+25°C
2, 5 TA=TC=+125°C
3, 6 TA=TC= -55°C
7 Device has internal shutdown feature that pulses the output with a low duty cycle during faults.
6
Rev. E 12/04
MSK [ M.S. KENNEDY CORPORATION ]
