欢迎访问ic37.com |
会员登录 免费注册
发布采购

MT88L89AE 参数 Datasheet PDF下载

MT88L89AE图片预览
型号: MT88L89AE
PDF下载: 下载PDF文件 查看货源
内容描述: 3V集成DTMFTransceiver自适应微型接口 [3V Integrated DTMFTransceiver with Adaptive Micro Interface]
分类和应用: 电信集成电路光电二极管
文件页数/大小: 20 页 / 355 K
品牌: MITEL [ MITEL NETWORKS CORPORATION ]
 浏览型号MT88L89AE的Datasheet PDF文件第12页浏览型号MT88L89AE的Datasheet PDF文件第13页浏览型号MT88L89AE的Datasheet PDF文件第14页浏览型号MT88L89AE的Datasheet PDF文件第15页浏览型号MT88L89AE的Datasheet PDF文件第16页浏览型号MT88L89AE的Datasheet PDF文件第18页浏览型号MT88L89AE的Datasheet PDF文件第19页浏览型号MT88L89AE的Datasheet PDF文件第20页  
Advance Information  
MT88L89  
AC Electrical Characteristics- MPU Interface - Voltages are with respect to ground (VSS), unless otherwise stated.  
Characteristics  
Sym  
Min  
Typ  
Max  
Units  
Conditions  
Figure 15  
1
2
3
4
5
6
7
8
9
DS/RD/WR clock frequency  
DS/RD/WR cycle period  
DS/RD/WR low pulse width  
DS/RD/WR high pulse width  
DS/RD/WR rise and fall time  
R/W setup time  
fCYC  
tCYC  
tCL  
4.0  
250  
150  
100  
20  
0
MHz  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
Figure 15  
Figure 15  
tCH  
Figure 15  
tR,tF  
tRWS  
tRWH  
tAS  
Figure 15  
Figures 16 & 17  
Figures 16 & 17  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
Figures 16 - 19  
R/W hold time  
26  
0
Address setup time (RS0)  
Address hold time (RS0)  
tAH  
26  
22  
80  
35  
10  
45  
40  
10 Data hold time (read)  
11 DS/RD to valid data delay (read)  
12 Data setup time (write)  
13 Data hold time (write)  
14 Chip select setup time  
15 Chip select hold time  
tDHR  
tDDR  
tDSW  
tDHW  
tCSS  
tCSH  
† Characteristics are over recommended operating conditions unless otherwise stated  
‡ Typical figures are at 25°C, VDD=3V, and for design aid only: not guaranteed and not subject to production testing  
NOTES: 1) dBm=decibels above or below a reference power of 1 mW into a 600 ohm load.  
2) Digit sequence consists of all 16 DTMF tones.  
3) Tone duration=40 ms. Tone pause=40 ms.  
4) Nominal DTMF frequencies are used.  
5) Both tones in the composite signal have an equal amplitude.  
6) The tone pair is deviated by ± 1.5 %±2 Hz.  
7) Bandwidth limited (3 kHz) Gaussian noise.  
8) The precise dial tone frequencies are 350 and 440 Hz (±2 %).  
9) Guaranteed by design and characterization. Not subject to production testing.  
10) Referenced to the lowest amplitude tone in the DTMF signal.  
11) For guard time calculation purposes.  
tCYC  
tR  
tF  
tCH  
tCL  
DS/RD/WR  
Figure 15 - DS/RD/WR Clock Pulse  
4-141