欢迎访问ic37.com |
会员登录 免费注册
发布采购

HAL825UT-K 参数 Datasheet PDF下载

HAL825UT-K图片预览
型号: HAL825UT-K
PDF下载: 下载PDF文件 查看货源
内容描述: 高精度可编程线性霍尔效应传感器系列 [High-Precision Programmable Linear Hall-Effect Sensor Family]
分类和应用: 传感器换能器
文件页数/大小: 32 页 / 1642 K
品牌: MICRONAS [ MICRONAS ]
 浏览型号HAL825UT-K的Datasheet PDF文件第20页浏览型号HAL825UT-K的Datasheet PDF文件第21页浏览型号HAL825UT-K的Datasheet PDF文件第22页浏览型号HAL825UT-K的Datasheet PDF文件第23页浏览型号HAL825UT-K的Datasheet PDF文件第25页浏览型号HAL825UT-K的Datasheet PDF文件第26页浏览型号HAL825UT-K的Datasheet PDF文件第27页浏览型号HAL825UT-K的Datasheet PDF文件第28页  
HAL82x  
DATA SHEET  
4.4. Ambient Temperature  
Temperature  
TC-Range TC  
TCSQ  
Coefficient of  
Magnet (ppm/K)  
Due to the internal power dissipation, the temperature  
on the silicon chip (junction temperature TJ) is higher  
than the temperature outside the package (ambient  
temperature TA).  
500  
1
2
2
2
2
2
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
1
3
6
7
2
5
0
3
7
1
6
6
7
2
6
1
0
5
5
1
6
3
7
1
4
600  
31  
28  
24  
20  
16  
16  
12  
12  
8
700  
TJ = TA + ΔT  
800  
900  
At static conditions and continuous operation, the fol-  
lowing equation applies:  
1000  
1100  
1200  
1300  
1400  
1500  
1600  
1700  
1800  
1900  
2000  
2100  
2200  
2400  
2500  
2600  
2800  
2900  
3000  
3100  
3300  
3500  
ΔT = IDD × VDD × RthJ  
For typical values, use the typical parameters. For  
worst case calculation, use the max. parameters for  
IDD and Rth, and the max. value for VDD from the appli-  
cation.  
4
4
0
For VDD = 5.5 V, Rth = 235 K/W, and IDD = 10 mA, the  
temperature difference ΔT = 12.93 K.  
31  
28  
28  
24  
24  
20  
16  
14  
12  
8
For all sensors, the junction temperature TJ is speci-  
fied. The maximum ambient temperature TAmax can be  
calculated as:  
TAmax = TLmax ΔT  
4.5. EMC and ESD  
The HAL82x is designed for a stabilized 5 V supply.  
Interferences and disturbances conducted along the  
12 V on board system (product standard ISO 7637  
part 1) are not relevant for these applications.  
8
For applications with disturbances by capacitive or  
inductive coupling on the supply line or radiated distur-  
bances, the application circuit shown in Fig. 4–1 is rec-  
ommended. Applications with this arrangement should  
pass the EMC tests according to the product stan-  
dards ISO 7637 part 3 (Electrical transient transmis-  
sion by capacitive or inductive coupling).  
4
4
0
Please contact Micronas for the detailed investigation  
reports with the EMC and ESD results.  
Note: The above table shows only some approximate  
values. Micronas recommends to use the TC-  
Calc software to find optimal settings for temper-  
ature coefficients. Please contact Micronas for  
more detailed information.  
24  
Feb. 3, 2009; DSH000143_003EN  
Micronas