欢迎访问ic37.com |
会员登录 免费注册
发布采购

MT250QL01GABA8ESF0AITES 参数 Datasheet PDF下载

MT250QL01GABA8ESF0AITES图片预览
型号: MT250QL01GABA8ESF0AITES
PDF下载: 下载PDF文件 查看货源
内容描述: [3V, Multiple I/O, 4KB, 32KB, 64KB, Sector Erase]
分类和应用:
文件页数/大小: 97 页 / 1038 K
品牌: MICRON [ MICRON TECHNOLOGY ]
 浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第68页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第69页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第70页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第71页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第73页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第74页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第75页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第76页  
256Mb, 3V Multiple I/O Serial Flash Memory  
ADDRESS MODE Operations  
ADDRESS MODE Operations  
ENTER and EXIT 4-BYTE ADDRESS MODE Command  
To initiate these commands, S# is driven LOW, and the command is input on DQn.  
Table 33: ENTER and EXIT 4-BYTE ADDRESS MODE Operations  
Operation Name  
Description/Conditions  
ENTER 4-BYTE ADDRESS MODE (B7h) The effect of the command is immediate. The default address mode is three bytes,  
and the device returns to the default upon exiting the 4-byte address mode.  
EXIT 4-BYTE ADDRESS MODE (E9h)  
DEEP POWER-DOWN Operations  
ENTER DEEP POWER-DOWN Command  
To execute ENTER DEEP POWER-DOWN, S# must be driven HIGH after the eighth bit  
of the command code is latched in, after which, tDP time must elapse before the supply  
current is reduced to ICC2.. Any attempt to execute ENTER DEEP POWER-DOWN during  
a WRITE operation is rejected without affecting the operation.  
In deep power-down mode, no device error bits are set, the WEL state is unchanged,  
and the device ignores all commands except RELEASE FROM DEEP POWER-DOWN,  
RESET ENABLE, RESET, hardware reset, and power-loss rescue sequence commands.  
RELEASE FROM DEEP POWER-DOWN Command  
To execute the RELEASE FROM DEEP POWER-DOWN command, S# is driven LOW, fol-  
lowed by the command code. Sending additional clock cycles on C while S# is driven  
LOW voids the command.  
RELEASE FROM DEEP POWER-DOWN is terminated by driving S# HIGH. The device  
enters standby mode after S# is driven HIGH followed by a delay of tRDP. S# must re-  
main HIGH during this time.  
Table 34: DEEP POWER-DOWN Operations  
Operation Name  
Description/Conditions  
ENTER DEEP  
POWER-DOWN (B9h)  
The command is used to place the device in deep power-down mode for the lowest device  
power consumption, with device current reduced to ICC2. This command can also be used as  
a software protection mechanism while the device is not in active use.  
RELEASE FROM  
DEEP POWER-DOWN (ABh)  
The command is used to exit from deep power-down mode. The device also exits deep  
power-down mode upon:  
A power-down, entering standby mode with the next power-up.  
A hardware or software reset operation, entering standby mode with a recovery time as  
specified in the AC Reset Specifications.  
CCMTD-1725822587-3368  
mt25q-qljs-L256-ABA-xxT.pdf - Rev. K 07/18 EN  
Micron Technology, Inc. reserves the right to change products or specifications without notice.  
72  
© 2014 Micron Technology, Inc. All rights reserved.  
 
 
 
 
 
 
 
 复制成功!