PIC18F2450/4450
TABLE 19-2: PIC18FXXXX INSTRUCTION SET (CONTINUED)
16-Bit Instruction Word
Mnemonic,
Operands
Status
Affected
Description
Cycles
Notes
MSb LSb
BIT-ORIENTED OPERATIONS
BCF
BSF
BTFSC
BTFSS
BTG
f, b, a Bit Clear f
f, b, a Bit Set f
f, b, a Bit Test f, Skip if Clear
f, b, a Bit Test f, Skip if Set
f, d, a Bit Toggle f
1
1
1001 bbba ffff ffff None
1000 bbba ffff ffff None
1, 2
1, 2
3, 4
3, 4
1, 2
1 (2 or 3) 1011 bbba ffff ffff None
1 (2 or 3) 1010 bbba ffff ffff None
1
0111 bbba ffff ffff None
CONTROL OPERATIONS
BC
BN
n
n
n
n
n
n
n
n
Branch if Carry
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
1 (2)
2
1110 0010 nnnn nnnn None
1110 0110 nnnn nnnn None
1110 0011 nnnn nnnn None
1110 0111 nnnn nnnn None
1110 0101 nnnn nnnn None
1110 0001 nnnn nnnn None
1110 0100 nnnn nnnn None
1101 0nnn nnnn nnnn None
1110 0000 nnnn nnnn None
1110 110s kkkk kkkk None
1111 kkkk kkkk kkkk
Branch if Negative
Branch if Not Carry
Branch if Not Negative
Branch if Not Overflow
Branch if Not Zero
Branch if Overflow
Branch Unconditionally
Branch if Zero
BNC
BNN
BNOV
BNZ
BOV
BRA
BZ
n
n, s
1 (2)
2
CALL
Call subroutine 1st word
2nd word
CLRWDT
DAW
GOTO
—
—
n
Clear Watchdog Timer
Decimal Adjust WREG
Go to address 1st word
2nd word
1
1
2
0000 0000 0000 0100 TO, PD
0000 0000 0000 0111
C
1110 1111 kkkk kkkk None
1111 kkkk kkkk kkkk
NOP
NOP
POP
PUSH
RCALL
RESET
RETFIE
—
—
—
—
n
No Operation
No Operation
1
1
1
1
2
1
2
0000 0000 0000 0000 None
1111 xxxx xxxx xxxx None
0000 0000 0000 0110 None
0000 0000 0000 0101 None
1101 1nnn nnnn nnnn None
0000 0000 1111 1111 All
0000 0000 0001 000s GIE/GIEH,
PEIE/GIEL
4
Pop top of return stack (TOS)
Push top of return stack (TOS)
Relative Call
Software device Reset
Return from interrupt enable
s
RETLW
RETURN
SLEEP
k
s
—
Return with literal in WREG
Return from Subroutine
Go into Standby mode
2
2
1
0000 1100 kkkk kkkk None
0000 0000 0001 001s None
0000 0000 0000 0011 TO, PD
Note 1: When a PORT register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that
value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as an input and is
driven low by an external device, the data will be written back with a ‘0’.
2: If this instruction is executed on the TMR0 register (and where applicable, ‘d’ = 1), the prescaler will be cleared if
assigned.
3: If the Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The
second cycle is executed as a NOP.
4: Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP
unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all
program memory locations have a valid instruction.
© 2006 Microchip Technology Inc.
Advance Information
DS39760A-page 215
MICROCHIP [ MICROCHIP ]
