PIC18F2450/4450
3. Ensure bits CREN and SREN are clear.
4. If interrupts are desired, set enable bit RCIE.
5. If 9-bit reception is desired, set bit RX9.
6. If a single reception is required, set bit SREN.
For continuous reception, set bit CREN.
7. Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
the enable bit RCIE was set.
8. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
15.3.2
EUSART SYNCHRONOUS MASTER
RECEPTION
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RX pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
9. Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
11. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
To set up a Synchronous Master Reception:
1. Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
2. Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
FIGURE 15-13:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT
pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
RC6/TX/CK pin
(SCKP = 0)
RC6/TX/CK pin
(SCKP = 1)
Write to
bit SREN
SREN bit
CREN bit
‘0’
‘0’
RCIF bit
(Interrupt)
Read
RXREG
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1and bit BRGH = 0.
TABLE 15-8: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Reset
Values
on page
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON
PIR1
GIE/GIEH PEIE/GIEL
TMR0IE
RCIF
INT0IE
TXIF
RBIE
—
TMR0IF INT0IF
RBIF
49
51
51
51
51
50
51
51
51
50
—
—
ADIF
ADIE
ADIP
RX9
CCP1IF TMR2IF TMR1IF
CCP1IE TMR2IE TMR1IE
CCP1IP TMR2IP TMR1IP
PIE1
RCIE
TXIE
—
IPR1
—
RCIP
TXIP
—
RCSTA
RCREG
TXSTA
SPEN
SREN
CREN
ADDEN
FERR
OERR
RX9D
EUSART Receive Register
CSRC
TX9
TXEN
—
SYNC
SCKP
SENDB
BRG16
BRGH
—
TRMT
WUE
TX9D
BAUDCON ABDOVF
RCIDL
ABDEN
SPBRGH EUSART Baud Rate Generator Register High Byte
SPBRG EUSART Baud Rate Generator Register Low Byte
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
DS39760A-page 170
Advance Information
© 2006 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
