PIC18F2331/2431/4331/4431
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F2331/2431/4331/4431 (Industrial, Extended)
PIC18LF2331/2431/4331/4431 (Industrial) (Continued)
PIC18LF2331/2431/4331/4431
Standard Operating Conditions (unless otherwise stated)
(Industrial)
Operating temperature
-40°C TA +85°C for industrial
Standard Operating Conditions (unless otherwise stated)
PIC18F2331/2431/4331/4431
Operating temperature
-40°C TA +85°C for industrial
-40°C TA +125°C for extended
(Industrial, Extended)
Param
Device
No.
Typ
Max Units
Conditions
(2,3)
Supply Current (IDD)
PIC18LF2X31/4X31
35
35
35
55
50
60
50
50
A
A
A
A
A
A
A
A
A
A
-40°C
+25°C
+85°C
-40°C
VDD = 2.0V
60
PIC18LF2X31/4X31
80
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
80
+25°C
+85°C
-40°C
VDD = 3.0V
VDD = 5.0V
100
150
150
150
400
All devices 105
110
115
300
+25°C
+85°C
+125°C
PIC18LF2X31/4X31 135
180
180
180
280
280
280
525
525
525
1.7
A
A
A
A
A
A
A
A
A
mA
-40°C
+25°C
+85°C
-40°C
140
VDD = 2.0V
VDD = 3.0V
140
PIC18LF2X31/4X31 215
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
225
+25°C
+85°C
-40°C
230
All devices 410
420
+25°C
+85°C
+125°C
VDD = 5.0V
430
1.2
All devices
18
FOSC = 25 MHz
(PRI_IDLE mode,
EC oscillator)
22
mA
+125°C
VDD = 5.0V
VDD = 4.2 V
All devices 3.2
4.1
4.1
4.1
5.1
5.1
5.1
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
3.2
FOSC = 40 MHz
(PRI_IDLE mode,
EC oscillator)
3.3
All devices 4.0
4.1
4.1
VDD = 5.0V
Legend:
Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula: Ir = VDD/2REXT (mA) with REXT in k.
4: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
DS39616D-page 336
2010 Microchip Technology Inc.