PIC18F2331/2431/4331/4431
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F2331/2431/4331/4431 (Industrial, Extended)
PIC18LF2331/2431/4331/4431 (Industrial) (Continued)
PIC18LF2331/2431/4331/4431
Standard Operating Conditions (unless otherwise stated)
(Industrial)
Operating temperature
-40°C TA +85°C for industrial
Standard Operating Conditions (unless otherwise stated)
PIC18F2331/2431/4331/4431
Operating temperature
-40°C TA +85°C for industrial
-40°C TA +125°C for extended
(Industrial, Extended)
Param
Device
No.
Typ
Max Units
Conditions
(2,3)
Supply Current (IDD)
PIC18LF2X31/4X31 150
250
250
250
350
350
350
1.0
1.0
1.0
2.1
600
600
600
1.0
1.0
1.0
2.0
2.0
2.0
4.2
A
A
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
150
VDD = 2.0V
160
A
PIC18LF2X31/4X31 340
A
FOSC = 1 MHZ
(PRI_RUN,
EC oscillator)
300
A
VDD = 3.0V
VDD = 5.0V
280
A
All devices 0.72
mA
mA
mA
mA
A
0.63
0.57
0.9
PIC18LF2X31/4X31 440
450
A
VDD = 2.0V
VDD = 3.0V
460
A
PIC18LF2X31/4X31 0.80
mA
mA
mA
mA
mA
mA
mA
FOSC = 4 MHz
(PRI_RUN,
0.78
0.77
EC oscillator)
All devices 1.6
1.5
VDD = 5.0V
1.5
2.0
All devices
10
FOSC = 25 MHz
(PRI_RUN,
EC oscillator)
28
mA
+125°C
VDD = 5.0V
VDD = 4.2V
VDD = 5.0V
All devices 9.5
12
12
12
15
15
15
mA
mA
mA
mA
mA
mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
9.7
FOSC = 40 MHZ
(PRI_RUN,
EC oscillator)
9.9
All devices 11.9
12.1
12.3
Legend:
Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula: Ir = VDD/2REXT (mA) with REXT in k.
4: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
2010 Microchip Technology Inc.
DS39616D-page 335
MICROCHIP [ MICROCHIP ]
