欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC18F2320-I/SP 参数 Datasheet PDF下载

PIC18F2320-I/SP图片预览
型号: PIC18F2320-I/SP
PDF下载: 下载PDF文件 查看货源
内容描述: 28 /40/ 44引脚高性能,增强型闪存微控制器与10位A / D和纳瓦技术 [28/40/44-Pin High-Performance, Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology]
分类和应用: 闪存微控制器和处理器外围集成电路光电二极管PC时钟
文件页数/大小: 388 页 / 6899 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC18F2320-I/SP的Datasheet PDF文件第176页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第177页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第178页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第179页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第181页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第182页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第183页浏览型号PIC18F2320-I/SP的Datasheet PDF文件第184页  
PIC18F2220/2320/4220/4320  
If the general call address matches, the SSPSR is  
transferred to the SSPBUF, the BF flag bit is set (eighth  
bit) and on the falling edge of the ninth bit (ACK bit), the  
SSPIF interrupt flag bit is set.  
17.4.5  
GENERAL CALL ADDRESS  
SUPPORT  
The addressing procedure for the I2C bus is such that  
the first byte after the Start condition usually deter-  
mines which device will be the slave addressed by the  
master. The exception is the general call address,  
which can address all devices. When this address is  
used, all devices should, in theory, respond with an  
Acknowledge.  
When the interrupt is serviced, the source for the inter-  
rupt can be checked by reading the contents of the  
SSPBUF. The value can be used to determine if the  
address was device specific or a general call address.  
In 10-bit mode, the SSPADD is required to be updated  
for the second half of the address to match and the UA  
bit is set (SSPSTAT<1>). If the general call address is  
sampled when the GCEN bit is set while the slave is  
configured in 10-bit Address mode, then the second  
half of the address is not necessary, the UA bit will not  
be set and the slave will begin receiving data after the  
Acknowledge (Figure 17-15).  
The general call address is one of eight addresses  
reserved for specific purposes by the I2C protocol. It  
consists of all ‘0’s with R/W = 0.  
The general call address is recognized when the  
General Call Enable bit (GCEN) is enabled  
(SSPCON2<7> set). Following a Start bit detect, 8 bits  
are shifted into the SSPSR and the address is com-  
pared against the SSPADD. It is also compared to the  
general call address and fixed in hardware.  
FIGURE 17-15:  
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE  
(7 OR 10-BIT ADDRESS MODE)  
Address is compared to general call address  
after ACK, set interrupt  
Receiving Data  
D5 D4 D3 D2 D1  
ACK  
R/W = 0  
General Call Address  
ACK  
SDA  
SCL  
D7 D6  
D0  
8
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
9
S
SSPIF  
BF (SSPSTAT<0>)  
Cleared in software  
SSPBUF is read  
SSPOV (SSPCON1<6>)  
GCEN (SSPCON2<7>)  
0’  
1’  
DS39599C-page 178  
2003 Microchip Technology Inc.  
 复制成功!