欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC16C620A-04E/SS 参数 Datasheet PDF下载

PIC16C620A-04E/SS图片预览
型号: PIC16C620A-04E/SS
PDF下载: 下载PDF文件 查看货源
内容描述: 基于EPROM的8位CMOS微控制器 [EPROM-Based 8-Bit CMOS Microcontroller]
分类和应用: 微控制器和处理器外围集成电路光电二极管可编程只读存储器电动程控只读存储器时钟
文件页数/大小: 108 页 / 622 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第56页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第57页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第58页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第59页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第61页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第62页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第63页浏览型号PIC16C620A-04E/SS的Datasheet PDF文件第64页  
PIC16C62X  
9.9  
Code Protection  
9.11  
In-Circuit Serial Programming  
If the code protection bit(s) have not been  
programmed, the on-chip program memory can be  
read out for verification purposes.  
The PIC16C62X microcontrollers can be serially  
programmed while in the end application circuit.This is  
simply done with two lines for clock and data, and three  
other lines for power, ground, and the programming  
voltage. This allows customers to manufacture boards  
with unprogrammed devices, and then program the  
microcontroller just before shipping the product. This  
also allows the most recent firmware or a custom  
firmware to be programmed.  
Note: Microchip does not recommend code  
protecting windowed devices.  
9.10  
ID Locations  
Four memory locations (2000h-2003h) are designated  
as ID locations where the user can store checksum or  
other code-identification numbers. These locations are  
not accessible during normal execution but are  
readable and writable during program/verify. Only the  
least significant 4 bits of the ID locations are used.  
The device is placed into a program/verify mode by  
holding the RB6 and RB7 pins low while raising the  
MCLR (VPP) pin from VIL to VIHH (see programming  
specification). RB6 becomes the programming clock  
and RB7 becomes the programming data. Both RB6  
and RB7 are Schmitt Trigger inputs in this mode.  
After reset, to place the device into programming/verify  
mode, the program counter (PC) is at location 00h. A  
6-bit command is then supplied to the device.  
Depending on the command, 14-bits of program data  
are then supplied to or from the device, depending if the  
command was a load or a read. For complete details of  
serial  
programming,  
please  
refer  
to  
the  
PIC16C6X/7X/9XX  
(#DS30228).  
Programming  
Specifications  
A typical in-circuit serial programming connection is  
shown in Figure 9-19.  
FIGURE 9-19: TYPICAL IN-CIRCUIT SERIAL  
PROGRAMMING  
CONNECTION  
To Normal  
Connections  
External  
Connector  
Signals  
PIC16C62X  
+5V  
0V  
VDD  
VSS  
VPP  
MCLR/VPP  
RB6  
RB7  
CLK  
Data I/O  
VDD  
To Normal  
Connections  
DS30235G-page 60  
Preliminary  
1998 Microchip Technology Inc.  
 
 复制成功!