PIC16C71X
Applicable Devices 710 71 711 715
11.3
DC Characteristics:
PIC16C710-04 (Commercial, Industrial, Extended)
PIC16C711-04 (Commercial, Industrial, Extended)
PIC16C710-10 (Commercial, Industrial, Extended)
PIC16C711-10 (Commercial, Industrial, Extended)
PIC16C710-20 (Commercial, Industrial, Extended)
PIC16C711-20 (Commercial, Industrial, Extended)
PIC16LC710-04 (Commercial, Industrial, Extended)
PIC16LC711-04 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature 0˚C
-40˚C
-40˚C
≤ TA ≤ +70˚C (commercial)
≤ TA ≤ +85˚C (industrial)
≤ TA ≤ +125˚C (extended)
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 11.1 and
Section 11.2.
Param
No.
Characteristic
Sym
Min Typ Max Units
†
Conditions
Input Low Voltage
I/O ports
VIL
D030
with TTL buffer
VSS
VSS
VSS
VSS
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
V
V
V
V
For entire VDD range
4.5 ≤ VDD ≤ 5.5V
D030A
D031
D032
with Schmitt Trigger buffer
MCLR, OSC1
(in RC mode)
D033
OSC1 (in XT, HS and LP)
Input High Voltage
I/O ports
VSS
-
0.3VDD
V
Note1
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
VDD
VDD
V
V
4.5 ≤ VDD ≤ 5.5V
For entire VDD range
0.25VDD
+ 0.8V
0.8VDD
0.8VDD
0.7VDD
0.9VDD
50
D041
D042
with Schmitt Trigger buffer
MCLR, RB0/INT
-
-
-
-
VDD
VDD
VDD
VDD
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043
D070
OSC1 (in RC mode)
PORTB weak pull-up current
Input Leakage Current (Notes 2, 3)
I/O ports
IPURB
IIL
250 400
µA VDD = 5V, VPIN = VSS
D060
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-
impedance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and LP
osc configuration
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C7X be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30272A-page 92
1997 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
