PIC16F7X
8.4.1
CCP PIN CONFIGURATION
8.4.4
SPECIAL EVENT TRIGGER
The user must configure the RC2/CCP1 pin as an out-
put by clearing the TRISC<2> bit.
In this mode, an internal hardware trigger is generated,
which may be used to initiate an action.
The special event trigger output of CCP1 resets the
TMR1 register pair. This allows the CCPR1 register to
effectively be a 16-bit programmable period register for
Timer1.
Note: Clearing the CCP1CON register will force
the RC2/CCP1 compare output latch to the
default low level. This is not the PORTC
I/O data latch.
The special event trigger output of CCP2 resets the
TMR1 register pair and starts an A/D conversion (if the
A/D module is enabled).
8.4.2
TIMER1 MODE SELECTION
Timer1 must be running in Timer mode or Synchro-
nized Counter mode if the CCP module is using the
compare feature. In Asynchronous Counter mode, the
compare operation may not work.
Note: The special event trigger from the CCP1
and CCP2 modules will not set interrupt
flag bit TMR1IF (PIR1<0>).
8.4.3
SOFTWARE INTERRUPT MODE
When Generate Software Interrupt mode is chosen, the
CCP1 pin is not affected. The CCP1IF or CCP2IF bit is
set, causing a CCP interrupt (if enabled).
TABLE 8-3:
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1
Value on:
POR,
BOR
Value on
all other
RESETS
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0Bh,8Bh, INTCON
10Bh,18Bh
GIE
PEIE TMR0IE
INTE
RBIE
TMR0IF
INTF
RBIF 0000 000x 0000 000u
(1)
0Ch
0Dh
8Ch
8Dh
87h
0Eh
0Fh
10h
15h
16h
17h
1Bh
1Ch
1Dh
PIR1
PSPIF
ADIF
—
RCIF
—
TXIF
—
SSPIF
—
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
CCP2IF ---- ---0 ---- ---0
CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
PIR2
—
—
—
(1)
PIE1
PSPIE
—
ADIE
—
RCIE
—
TXIE
—
SSPIE
—
PIE2
—
—
CCP2IE ---- ---0 ---- ---0
1111 1111 1111 1111
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
TRISC
TMR1L
TMR1H
T1CON
PORTC Data Direction Register
Holding Register for the Least Significant Byte of the 16-bit TMR1 Register
Holding Register for the Most Significant Byte of the 16-bit TMR1 Register
—
—
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
CCPR1L Capture/Compare/PWM Register1 (LSB)
CCPR1H Capture/Compare/PWM Register1 (MSB)
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
CCP1CON
—
—
CCP1X
CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
CCPR2L Capture/Compare/PWM Register2 (LSB)
CCPR2H Capture/Compare/PWM Register2 (MSB)
xxxx xxxx uuuu uuuu
xxxx xxxx uuuu uuuu
CCP2CON
—
—
CCP2X
CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0 --00 0000 --00 0000
Legend: x= unknown, u= unchanged, -= unimplemented, read as '0'. Shaded cells are not used by Capture and Timer1.
Note 1: The PSP is not implemented on the PIC16F73/76; always maintain these bits clear.
DS30325B-page 56
2002 Microchip Technology Inc.