PIC16F7X
8.3.4
CCP PRESCALER
8.3
Capture Mode
There are four prescaler settings, specified by bits
CCP1M3:CCP1M0. Whenever the CCP module is
turned off, or the CCP module is not in Capture mode,
the prescaler counter is cleared. Any RESET will clear
the prescaler counter.
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register when an event occurs
on pin RC2/CCP1. An event is defined as one of the fol-
lowing and is configured by CCPxCON<3:0>:
• Every falling edge
• Every rising edge
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared, therefore, the first capture may be from
a non-zero prescaler. Example 8-1 shows the recom-
mended method for switching between capture pres-
calers. This example also clears the prescaler counter
and will not generate the “false” interrupt.
• Every 4th rising edge
• Every 16th rising edge
An event is selected by control bits CCP1M3:CCP1M0
(CCP1CON<3:0>). When a capture is made, the inter-
rupt request flag bit CCP1IF (PIR1<2>) is set. The
interrupt flag must be cleared in software. If another
capture occurs before the value in register CCPR1 is
read, the old captured value is overwritten by the new
captured value.
EXAMPLE 8-1:
CHANGING BETWEEN
CAPTURE PRESCALERS
;Turn CCP module off
CLRF
CCP1CON
MOVLW
NEW_CAPT_PS;Load the W reg with
;the new prescaler
8.3.1
CCP PIN CONFIGURATION
;move value and CCP ON
;Load CCP1CON with this
;value
In Capture mode, the RC2/CCP1 pin should be config-
ured as an input by setting the TRISC<2> bit.
MOVWF
CCP1CON
Note: If the RC2/CCP1 pin is configured as an
output, a write to the port can cause a
capture condition.
8.4
Compare Mode
In Compare mode, the 16-bit CCPR1 register value is
constantly compared against the TMR1 register pair
value. When a match occurs, the RC2/CCP1 pin is:
FIGURE 8-1:
CAPTURE MODE
OPERATION BLOCK
DIAGRAM
• Driven high
• Driven low
Set Flag bit CCP1IF
(PIR1<2>)
Prescaler
• Remains unchanged
÷ 1, 4, 16
The action on the pin is based on the value of control
bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the
same time, interrupt flag bit CCP1IF is set.
RC2/CCP1
pin
CCPR1H
CCPR1L
Capture
Enable
and
Edge Detect
FIGURE 8-2:
COMPARE MODE
OPERATION BLOCK
DIAGRAM
TMR1H
TMR1L
CCP1CON<3:0>
Q’s
CCP1CON<3:0>
Mode Select
8.3.2
TIMER1 MODE SELECTION
Set Flag bit CCP1IF
Timer1 must be running in Timer mode or Synchro-
nized Counter mode for the CCP module to use the
capture feature. In Asynchronous Counter mode, the
capture operation may not work.
(PIR1<2>)
CCPR1H CCPR1L
Comparator
Q
S
R
Output
Logic
Match
RC2/CCP1
Pin
8.3.3
SOFTWARE INTERRUPT
TMR1H TMR1L
TRISC<2>
Output Enable
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep bit
CCP1IE (PIE1<2>) clear to avoid false interrupts and
should clear the flag bit CCP1IF following any such
change in operating mode.
Special Event Trigger
Special Event Trigger will:
•
•
•
clear TMR1H and TMR1L registers
NOT set interrupt flag bit TMR1F (PIR1<0>)
(for CCP2 only) set the GO/DONE bit (ADCON0<2>)
2002 Microchip Technology Inc.
DS30325B-page 55