欢迎访问ic37.com |
会员登录 免费注册
发布采购

MCP4132-502E/MS 参数 Datasheet PDF下载

MCP4132-502E/MS图片预览
型号: MCP4132-502E/MS
PDF下载: 下载PDF文件 查看货源
内容描述: 7/8位单/双SPI数字电位器具有易失性存储器 [7/8-Bit Single/Dual SPI Digital POT with Volatile Memory]
分类和应用: 转换器电位器数字电位计存储电阻器光电二极管
文件页数/大小: 88 页 / 2525 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号MCP4132-502E/MS的Datasheet PDF文件第5页浏览型号MCP4132-502E/MS的Datasheet PDF文件第6页浏览型号MCP4132-502E/MS的Datasheet PDF文件第7页浏览型号MCP4132-502E/MS的Datasheet PDF文件第8页浏览型号MCP4132-502E/MS的Datasheet PDF文件第10页浏览型号MCP4132-502E/MS的Datasheet PDF文件第11页浏览型号MCP4132-502E/MS的Datasheet PDF文件第12页浏览型号MCP4132-502E/MS的Datasheet PDF文件第13页  
MCP413X/415X/423X/425X  
AC/DC CHARACTERISTICS (CONTINUED)  
Standard Operating Conditions (unless otherwise specified)  
Operating Temperature –40°C TA +125°C (extended)  
DC Characteristics  
All parameters apply across the specified operating ranges unless noted.  
VDD = +2.7V to 5.5V, 5 k, 10 k, 50 k, 100 kdevices.  
Typical specifications represent values for VDD = 5.5V, TA = +25°C.  
Parameters  
Sym  
Min  
Typ  
Max  
Units  
Conditions  
Digital Inputs/Outputs (CS, SDI, SDO, SCK, SHDN)  
Schmitt Trigger  
High Input  
Threshold  
VIH  
0.45 VDD  
V
2.7V VDD 5.5V  
(Allows 2.7V Digital VDD with  
5V Analog VDD  
)
0.5 VDD  
V
V
1.8V VDD 2.7V  
Schmitt Trigger  
Low Input  
VIL  
0.2VDD  
Threshold  
Hysteresis of  
Schmitt Trigger  
Inputs  
VHYS  
0.1VDD  
V
High Voltage Limit  
VMAX  
VOL  
VSS  
12.5 (6)  
0.3VDD  
0.3VDD  
VDD  
V
V
Pin can tolerate VMAX or less.  
IOL = 5 mA, VDD = 5.5V  
IOL = 1 mA, VDD = 1.8V  
IOH = -2.5 mA, VDD = 5.5V  
IOL = -1 mA, VDD = 1.8V  
Output Low  
Voltage (SDO)  
VSS  
V
Output High  
Voltage (SDO)  
VOH  
IPU  
0.7VDD  
0.7VDD  
V
VDD  
V
Weak Pull-up /  
1.75  
mA  
Internal VDD pull-up, VIHH pull-down,  
VDD = 5.5V, VCS = 12.5V  
Pull-down Current  
170  
16  
µA  
CS pin, VDD = 5.5V, VCS = 3V  
VDD = 5.5V, VCS = 3V  
CS Pull-up /  
Pull-down  
RCS  
kΩ  
Resistance  
Input Leakage  
Current  
IIL  
-1  
1
µA  
pF  
VIN = VDD and VIN = VSS  
fC = 20 MHz  
Pin Capacitance  
RAM (Wiper) Value  
Value Range  
CIN, COUT  
10  
N
N
0h  
0h  
1FFh  
1FFh  
hex  
hex  
hex  
hex  
8-bit device  
7-bit device  
8-bit device  
7-bit device  
POR/BOR Value  
80h  
40h  
Note 1: Resistance is defined as the resistance between terminal A to terminal B.  
2: INL and DNL are measured at VW with VA = VDD and VB = VSS  
.
3: MCP4XX1 only.  
4: MCP4XX2 only, includes VWZSE and VWFSE  
.
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.  
6: This specification by design.  
7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and  
temperature.  
8: The MCP4XX1 is externally connected to match the configurations of the MCP41X2 and MCP42X2, and  
then tested.  
9: POR/BOR is not rate dependent.  
10: Supply current is independent of current through the resistor network.  
© 2008 Microchip Technology Inc.  
DS22060B-page 9