欢迎访问ic37.com |
会员登录 免费注册
发布采购

ML4833CP 参数 Datasheet PDF下载

ML4833CP图片预览
型号: ML4833CP
PDF下载: 下载PDF文件 查看货源
内容描述: 电子调光镇流器控制器 [Electronic Dimming Ballast Controller]
分类和应用: 光电二极管信息通信管理电子控制器
文件页数/大小: 13 页 / 272 K
品牌: MICRO-LINEAR [ MICRO LINEAR CORPORATION ]
 浏览型号ML4833CP的Datasheet PDF文件第4页浏览型号ML4833CP的Datasheet PDF文件第5页浏览型号ML4833CP的Datasheet PDF文件第6页浏览型号ML4833CP的Datasheet PDF文件第7页浏览型号ML4833CP的Datasheet PDF文件第9页浏览型号ML4833CP的Datasheet PDF文件第10页浏览型号ML4833CP的Datasheet PDF文件第11页浏览型号ML4833CP的Datasheet PDF文件第12页  
ML4833  
Figure 4 shows the output configuration for the  
operational transconductance amplifiers.  
OSCILLATOR  
The VCO frequency ranges are controlled by the output  
of the LFB amplifier (R ). As lamp current increases,  
SET  
LFB OUT falls in voltage, causing the C charging current  
T
CURRENT  
MIRROR  
to increase, thereby causing the oscillator frequency to  
increase. Since the ballast output network attenuates high  
frequencies, the power to the lamp will be decreased.  
IN  
OUT  
gmV  
2
IN  
IQ +  
io = gmV  
IN  
gmV  
2
IN  
V
IQ –  
REF  
V
REF  
17  
CONTROL  
I
CHG  
R
T
IN  
OUT  
CURRENT  
MIRROR  
R /C  
T
T
+
7
1.25/3.75  
C
T
Figure 4. Output Configuration  
A DC path to ground or V at the output of the  
5.5mA  
CC  
transconductance amplifiers will introduce an offset error.  
The magnitude of the offset voltage that will appear at the  
input is given by V = io/gm. For an io of 1µA and a gm  
OS  
W
of 0.05 µW the input referred offset will be 20mV.  
Capacitor C1 as shown in Figure 3 is used to block the  
DC current to minimize the adverse effect of offsets.  
CLOCK  
= 3.75V  
Slew rate enhancement is incorporated into all of the  
operational transconductance amplifiers in the ML4833.  
This improves the recovery of the circuit in response to  
power up and transient conditions. The response to large  
signals will be somewhat non-linear as the transconductance  
amplifiers change from their low to high transconductance  
mode. This is illustrated in Figure 5.  
t
DIS  
t
CHG  
V
TH  
C
T
iO  
V
= 1.25V  
TL  
Figure 6. Oscillator Block Diagram and Timing  
V
IN  
Differential  
The oscillator frequency is determined by the following  
equations:  
0
Linear Slope Region  
1
FOSC  
=
(3)  
t
CHG + tDIS  
and  
V
V
+I R V  
REF CH  
T
TL  
Figure 5. Transconductance Amplifier Characteristics  
BALLAST OUTPUT SECTION  
t
= R C In  
T T  
(4)  
CHG  
+I R V  
TH  
REF CH  
T
The oscillator’s minimum frequency is set when I = 0  
CH  
The IC controls output power to the lamps via frequency  
modulation with non-overlapping conduction.This means  
that both ballast output drivers will be low during the  
where:  
1
FOSC  
discharging time t  
of the oscillator capacitor C .  
(5)  
DIS  
T
0.51×RTCT  
8