MAX691A/MAX693A/
MAX800L/MAX800M
Pin Description
PIN
1
2
3
4
5
6
NAME
VBATT
V
OUT
V
CC
Microprocessor Supervisory Circuits
FUNCTION
Battery-Backup Input. Connect to external battery or capacitor and charging circuit. If backup battery is
not used, connect to GND.
Output Supply Voltage. When V
CC
is greater than VBATT and above the reset threshold, V
OUT
connects
to V
CC
. When V
CC
falls below VBATT and is below the reset threshold, V
OUT
connects to VBATT. Connect
a 0.1µF capacitor from V
OUT
to GND. Connect V
OUT
to V
CC
if no backup battery is used.
Input Supply Voltage, 5V Input.
Ground. 0V reference for all signals.
Battery-On Output. When V
OUT
switches to VBATT, BATT ON goes high. When V
OUT
switches to V
CC,
BATT
ON goes low. Connect the base of a PNP through a current-limiting resistor to BATT ON for V
OUT
current
require- ments greater than 250mA.
LOW LINE
output goes low when V
CC
falls below the reset threshold. It returns high as soon as V
CC
rises above
the reset threshold.
External Oscillator Input. When OSC SEL is unconnected or driven high, a 10µA pull-up connects from V
OUT
to
OSC IN, the internal oscillator sets the reset and watchdog timeout periods, and OSC IN selects between
fast and slow watchdog timeout periods. When OSC SEL is driven low, the reset and watchdog timeout periods
may be set either by a capacitor from OSC IN to ground or by an external clock at OSC IN (Figure 3).
Oscillator Select. When OSC SEL is unconnected or driven high, the internal oscillator sets the reset
delay and watchdog timeout period. When OSC SEL is low, the external oscillator input (OSC IN) is enabled
(Table 1). OSC SEL has a 10µA internal pull-up.
Power-Fail Input. This is the noninverting input to the power-fail comparator. When PFI is less than 1.25V,
PFO
goes low. When PFI is not used, connect PFI to GND or V
OUT
.
Power-Fail Output. This is the output of the power-fail comparator.
PFO
goes low when PFI is less than 1.25V.
This is an uncommitted comparator, and has no effect on any other internal circuitry.
Watchdog Input. WDI is a three-level input. If WDI remains either high or low for longer than the watchdog
time- out period,
WDO
goes low and reset is asserted for the reset timeout period.
WDO
remains low until
the next tran- sition at WDI. Leaving WDI unconnected disables the watchdog function. WDI connects to an
internal voltage divider between V
OUT
and GND, which sets it to mid-supply when left unconnected.
Chip-Enable Output.
CE
OUT goes low only when
CE
IN is low and V
CC
is above the reset threshold. If CE
IN
is
low when reset is asserted,
CE
OUT will stay low for 15µs or until
CE
IN goes high, whichever occurs first.
Chip-Enable Input. The input to chip-enable gating circuit. If
CE
IN is not used, connect
CE
IN to GND or V
OUT.
Watchdog Output. If WDI remains high or low longer than the watchdog timeout period,
WDO
goes low and reset
is asserted for the reset timeout period.
WDO
returns high on the next transition at WDI.
WDO
remains high if
WDI
is
unconnected.
RESET
Output goes low whenever V
CC
falls below the reset threshold.
RESET
will remain low typically for
200ms after VCC crosses the reset threshold on power-up.
RESET is an active-high output. It is open drain, and the inverse of
RESET.
GND
BATT ON
LOW LINE
7
OSC IN
8
9
10
OSC SEL
PFI
PFO
11
WDI
12
13
14
15
16
CE
OUT
CE
IN
WDO
RESET
RESET
Detailed Description
RESET
and RESET Outputs
The MAX691A/MAX693A/MAX800L/MAX800M’s
RESET
and RESET outputs ensure that the μP (with reset inputs
asserted either high or low) powers up in a known state,
and prevents code-execution errors during power-down
or brownout conditions.
The
RESET
output is active low, and typically sinks 3.2mA
at 0.1V saturation voltage in its active state. When deas-
serted,
RESET
sources 1.6mA at typically V
OUT
- 0.5V.
RESET output is open drain, active high, and typically
www.maximintegrated.com
sinks 3.2mA with a saturation voltage of 0.1V. When no
backup battery is used,
RESET
output is guaranteed to be
valid down to V
CC
= 1V, and an external 10kΩ pulldown
resistor on
RESET
insures that it will be valid with V
CC
down to GND (Figure 1). As V
CC
goes below 1V, the gate
drive to the
RESET
output switch reduces accordingly,
increasing the R
DS(ON)
and the saturation voltage. The
10kΩ pulldown resistor insures the parallel combination
of switch plus resistor is around 10kΩ and the output
saturation voltage is below 0.4V while sinking 40μA. When
using a 10kΩ external pulldown resistor, the high state for
RESET
output with V
CC
= 4.75V will be 4.5V typical.
Maxim Integrated │ 7
MAXIM [ MAXIM INTEGRATED PRODUCTS ]
