®
LY6125616
5V 256K X 16 BIT HIGH SPEED CMOS SRAM
Rev. 2.4
ABSOLUTE MAXIMUN RATINGS*
PARAMETER
SYMBOL
VT1
RATING
-0.5 to 6.5
UNIT
V
Voltage on VCC relative to VSS
Voltage on any other pin relative to VSS
VT2
-0.5 to VCC+0.5
0 to 70(C grade)
-20 to 80(E grade)
-40 to 85(I grade)
-65 to 150
V
℃
Operating Temperature
TA
℃
W
Storage Temperature
Power Dissipation
DC Output Current
TSTG
PD
1
IOUT
50
mA
*Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device or any other conditions above those indicated in the operational sections of this specification is not
implied. Exposure to the absolute maximum rating conditions for extended period may affect device reliability.
TRUTH TABLE
I/O OPERATION
MODE
Standby
CE# OE# WE# LB# UB#
SUPPLY CURRENT
DQ0-DQ7
High – Z
High – Z
High – Z
DOUT
DQ8-DQ15
High – Z
High – Z
High – Z
High – Z
DOUT
H
L
L
L
L
L
L
L
L
X
H
X
L
L
L
X
X
X
X
H
X
H
H
H
L
X
X
H
L
H
L
L
H
L
X
X
H
H
L
L
H
L
ISB1
ICC
Output Disable
Read
High – Z
DOUT
ICC
DOUT
DIN
High – Z
DIN
High – Z
DIN
Write
L
L
ICC
L
DIN
Note: H = VIH, L = VIL, X = Don't care.
DC ELECTRICAL CHARACTERISTICS
SYMBOL
TEST CONDITION
MIN.
4.5
2.2
- 0.3
- 1
TYP. *4 MAX.
UNIT
PARAMETER
Supply Voltage
VCC
5.0
5.5
VCC+0.3
0.8
V
V
V
*1
Input High Voltage
Input Low Voltage
Input Leakage Current
Output Leakage
Current
VIH
VIL
-
-
-
*2
ILI
V
V
CC ≧ VIN ≧ VSS
CC ≧ VOUT ≧ VSS,
Output Disabled
1
A
µ
ILO
- 1
-
1
A
µ
Output High Voltage
Output Low Voltage
VOH IOH = -4mA
2.4
-
-
-
-
V
V
VOL
IOL = 8mA
-
-
-
-
-
-
-
-
0.4
10
15
20
25
215
140
110
100
15
mA
mA
mA
mA
mA
mA
Cycle time = Min.
Average Operating
Power supply Current
100
80
75
-
0.1
20
ICC
CE# = VIL , II/O = 0mA
Others at VIL or VIH
10
Standby Power
Supply Current
CE# ≧VCC - 0.2V
Others at 0.2V / VCC-0.2V
15/20/25
15/20/25LL
3*5
ISB1
100*6
A
µ
Notes:
1. VIH(max) = VCC + 2.0V for pulse width less than 6ns.
2. VIL(min) = VSS - 2.0V for pulse width less than 6ns.
3. Over/Undershoot specifications are characterized on engineering evaluation stage, not for mass production test.
4. Typical values are included for reference only and are not guaranteed or tested.
℃
Typical valued are measured at VCC = VCC(TYP.) and TA = 25
5. 1mA for special request
6. 50 A for special request
µ
Lyontek Inc. reserves the rights to change the specifications and products without notice.
5F, No. 2, Industry E. Rd. IX, Science-Based Industrial Park, Hsinchu 300, Taiwan.
TEL: 886-3-6668838
FAX: 886-3-6668836
4