LT1931/LT1931A
W U U
U
APPLICATIO S I FOR ATIO
The inductors shown in Table 2 for use with the LT1931A
were chosen for their small size. For better efficiency, use
similar valued inductors with a larger volume. For in-
stance, the Sumida CR43 series, in values ranging from
3.3µH to 10µH, will give a LT1931A application a few
percentage points increase in efficiency.
zero to the system. For the tantalum and OS-CON capaci-
tors, this zero is located at a lower frequency due to the
higher value of the ESR, while the zero of a ceramic
capacitor is at a much higher frequency and can generally
be ignored.
A phase lead zero can be intentionally introduced by
placing a capacitor (C4) in parallel with the resistor (R1)
between VOUT and VNFB as shown in Figure 1. The
frequency of the zero is determined by the following
equation.
CAPACITOR SELECTION
Low ESR (equivalent series resistance) capacitors should
beusedattheoutputtominimizetheoutputripplevoltage.
Multilayer ceramic capacitors are an excellent choice, as
they have an extremely low ESR and are available in very
small packages. X5R dielectrics are preferred, followed by
X7R, as these materials retain their capacitance over wide
voltage and temperature ranges. A 10µF to 22µF output
capacitor is sufficient for most LT1931 applications while
a 4.7µF to 10µF capacitor will suffice for the LT1931A.
Solid tantalum or OS-CON capacitors can be used, but
they will occupy more board area than a ceramic and will
haveahigherESR. Alwaysuseacapacitorwithasufficient
voltage rating.
1
ƒZ =
2π •R1•C4
By choosing the appropriate values for the resistor and
capacitor, the zero frequency can be designed to improve
the phase margin of the overall converter. The typical
target value for the zero frequency is between 20kHz to
60kHz. Figure 3 shows the transient response of the
inverting converter from Figure 1 without the phase lead
capacitor C4. The phase margin is reduced as evidenced
by more ringing in both the output voltage and inductor
current. A 220pF capacitor for C4 results in better phase
margin, which is revealed in Figure 4 as a more damped
responseandlessovershoot. Figure5showsthetransient
response when a 22µF tantalum capacitor with no phase
lead capacitor is used on the output. The higher output
voltage ripple is revealed in the upper waveform as a
thicker line. The transient response is adequate which
implies that the ESR zero is improving the phase margin.
Ceramic capacitors also make a good choice for the input
decoupling capacitor, which should be placed as close as
possible to the LT1931/LT1931A. A 1µF to 4.7µF input
capacitorissufficientformostapplications.Table3shows
a list of several ceramic capacitor manufacturers. Consult
the manufacturers for detailed information on their entire
selection of ceramic parts.
Table 3. Ceramic Capacitor Manufacturers
Taiyo Yuden
(408) 573-4150
www.t-yuden.com
VOUT
20mV/DIV
AC COUPLED
AVX
(803) 448-9411
www.avxcorp.com
Murata
(714) 852-2001
www.murata.com
I
L1A + IL1B
0.5A/DIV
AC COUPLED
200mA
100mA
LOAD
CURRENT
ThedecisiontouseeitherlowESR(ceramic)capacitorsor
the higher ESR (tantalum or OS-CON) capacitors can
effect the stability of the overall system. The ESR of any
capacitor, along with the capacitance itself, contributes a
100µs/DIV
1931 F03
Figure 3. Transient Response of Inverting Converter
Without Phase Lead Capacitor
1931fa
6