欢迎访问ic37.com |
会员登录 免费注册
发布采购

CAR2512TEBX5Z01A 参数 Datasheet PDF下载

CAR2512TEBX5Z01A图片预览
型号: CAR2512TEBX5Z01A
PDF下载: 下载PDF文件 查看货源
内容描述: [90VAC to 264VAC 12VDC@ 2500W; 3.3/5VDC standby @ 15W]
分类和应用:
文件页数/大小: 15 页 / 303 K
品牌: LINEAGEPOWER [ LINEAGE POWER CORPORATION ]
 浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第7页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第8页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第9页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第10页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第12页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第13页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第14页浏览型号CAR2512TEBX5Z01A的Datasheet PDF文件第15页  
Preliminary Data Sheet  
GE  
CAR2512TE Front-End  
Input: 90VAC to 264VAC; Output: 12 VDC @ 2500W; 3.3/5VDC standby @ 15W  
Operation command is used to turn the Power Supply ON or  
OFF via the PMBus. The data byte below follows the  
OPERATION command.  
Register  
Code Bit  
Function  
7
6
5
4
OV Fault/Warning detected  
OC Fault/Warning detected  
Input Fault/Warning detected  
Mfr_specific register change  
detected  
FUNCTION  
Unit ON  
DATA BYTE  
80  
00  
Unit OFF  
Status_word  
(includes Status_byte)  
79  
3
nPower_Good  
2
Fan Fault or Warning  
detected  
Other fault  
Unknown  
Vout OV Fault  
Vout OV Warning  
Vout UV Warning  
Vout UV Fault  
N/A  
N/A  
N/A  
N/A  
IOUT OC Fault  
To RESET the power supply cycle the power supply OFF, wait at  
least 2 seconds, and then turn back ON. All alarms and  
shutdowns are cleared during a restart.  
1
0
7
6
5
Clear_faults (03): This command clears all STATUS and FAULT  
registers and resets the SMBAlert# line.  
If a fault still persists after the issuance of the clear_faults  
command the specific registers indicating the fault are reset  
and the SMBAlert# line is activated again.  
4
3
Status_Vout  
Status_Iout  
7A  
2
1
0
7
6
5
WRITE_PROTECT register (10): Used to control writing to the  
PMBus device. The intent of this command is to provide  
protection against accidental changes. All supported  
command parameters may have their parameters read,  
regardless of the write_protect settings. The contents of this  
register can be stored to non-volatile memory using the  
Store_default_code command. The default setting of this  
register is disable_all_writes except write_protect 0x80h.  
N/A  
IOUT OC Warning  
N/A  
N/A  
N/A  
N/A  
N/A  
Vin OV Fault  
Vin OV Warning  
Vin UV Warning  
Vin UV Fault  
N/A  
4
3
7B  
2
1
0
7
6
5
FUNCTION  
DATA BYTE  
Enable all writes  
00  
80  
40  
Disable all writes except write_protect  
Disable all writes except write_protect and  
OPERATION  
4
3
Status_input  
7C  
Vout_Command (21) : This command is used to change the  
output voltage of the power supply. Changing the output  
voltage should be performed simultaneously to all power  
supplies operating in parallel using the Global Address  
(Broadcast) feature. If only a single power supply is instructed  
to change its output, it may attempt to source all the required  
power which can cause either a power limit or shutdown  
condition.  
2
1
0
7
6
5
N/A  
N/A  
N/A  
OT Fault  
OT Warning  
N/A  
N/A  
N/A  
N/A  
N/A  
N /A  
Fan 1 Fault  
Fan 2 Fault  
N/A  
4
3
Status_temperature  
7D  
2
1
0
7
6
5
Software programming of output voltage permanently  
overrides the set point voltage configured by the Vprog signal  
pin. The program no longer looks at the ‘Vprog pin’ and will not  
respond to any hardware voltage settings. If power is removed  
from the µController it will reset itself into its default  
configuration looking at the Vprog signal for output voltage  
control. In many applications, the Vprog pin is used for setting  
initial conditions, if different that the factory setting. Software  
programming then takes over once I2C communications are  
established.  
4
3
N/A  
Status_fan_1_2  
81  
Fan 1 Speed Overridden  
Fan 2 Speed Overridden  
N/A  
N/A  
3.3V_fault  
2
1
0
7
6
5
4
3
2
1
0
To properly hot-plug a power supply into a live backplane, the  
system generated voltage should get re-configured into either  
the factory adjusted firmware level or the voltage level  
reconfigured by the margin pin. Otherwise, the voltage state  
of the plugged in power supply could be significantly different  
than the powered system.  
OVSD  
Interrupt  
Fault detected  
PS_remote_OFF  
DC Fault  
Input Fault  
0 – AC high line,  
1 – AC low line  
Status_mfr_specific  
80  
Vout_OV_warn_limit (42): OV_warning is extremely useful  
because it gives the system controller a heads up that the  
output voltage is drifting out of regulation and the power  
supply is close to shutting down. Pre-amative action may be  
taken before the power supply would shut down and  
potentially disable the system.  
Command Descriptions  
Operation (01) : By default the Power supply is turned ON at  
power up as long as Power ON/OFF signal pin is active HI. The  
February 7, 2014  
©2013 General Electric Company. All rights reserved.  
Page 11