10 | Keysight | M9393A PXIe Performance Vector Signal Analyzer – Data Sheet
Technical Specifications and Characteristics
Standard Configuration - Options F08, F14, F18, F27
Amplitude (cont’d)
Amplitude repeatability and linearity
Pre-amp OFF, typical
± 0.03 dB
Pre-amp ON, typical
Repeatability 19
± 0.06 dB
Linearity 20
ADC dither high
Specification
ADC dither Low
Specification
Input signal relative to expected
input level setting
Typical
Typical
> –35 dB
0.08 dB
0.1 dB
0.03 dB
0.04 dB
0.08 dB
0.21 dB
0.03 dB
0.1 dB
≤ –35 dB
IF flatness, typical 21, 22
Across any 20 MHz Across any 20 MHz 40 MHz
100 MHz
160 MHz
in 40 MHz path
in 160 MHz path
≤ 13.6 GHz
± 0.08 dB
± 0.14 dB
± 0.16 dB
± 0.17 dB
± 0.21 dB
± 0.31 dB
± 0.34 dB
± 0.47 dB
> 13.6 GHz
± 0.12 dB
± 0.14 dB
IF phase linearity, typical 21, 22
Across any 20 MHz Across any 20 MHz 40 MHz
100 MHz
160 MHz
in 40 MHz path
in 160 MHz path
≤ 13.6 GHz
± 0.68 °
± 1.28 °
± 0.81 °
± 1.69 °
± 1.34 °
± 2.56 °
± 1.56 °
± 3.59 °
> 13.6 GHz
± 1.46 °
± 1.54 °
IF bandwidth filter switching uncertainty 23
Specification
Typical
Nominal
Preamp On
Preamp Off
± 0.3 dB
± 0.14 dB
± 0.25 dB
± 0.1 dB
± 0.2 dB
± 0.45 dB
Expected input level switching uncertainty 24
Pre-amp OFF 25
Pre-amp ON 26
≤ –3 dBm
Specification
± 0.48 dB
± 0.48 dB
± 0.39 dB
± 0.44 dB
± 0.34 dB
± 0.53 dB
± 0.78 dB
≤ –5 dBm
Specification
± 0.14 dB
± 0.18 dB
± 0.15 dB
± 0.16 dB
± 0.18 dB
± 0.16 dB
± 0.19 dB
± 0.18 dB
> –5 dBm
Typical
Specification
± 1.53 dB
± 1.56 dB
± 0.56 dB
± 0.53 dB
± 0.39 dB
± 0.71 dB
± 2.38 dB
± 1.39 dB
Typical
Typical
> 100 kHz to 1 MHz
> 1 to 20 MHz
± 0.03 dB
± 0.04 dB
± 0.04 dB
± 0.04 dB
± 0.05 dB
± 0.05 dB
± 0.05 dB
± 0.06 dB
± 0.6 dB
± 0.64 dB
± 0.24 dB
± 0.24 dB
± 0.15 dB
± 0.19 dB
± 0.39 dB
± 0.31 dB
± 0.18 dB
± 0.18 dB
± 0.15 dB
± 0.18 dB
± 0.12 dB
± 0.17 dB
± 0.17 dB
± 0.16 dB
> 20 to 100 MHz
> 100 MHz to 3.6 GHz
> 3.6 to 8 GHz
> 8 to 17 GHz
> 17 to 24 GHz
> 24 to 27 GHz
± 0.55 dB
19. Input level –11 dBm, LO nulling run at ~1 GHz, 150 ms allowed for amplitude settling, measurement made at 1 kHz from center of IF.
20. Input level 20 dB above the noise floor and ADC dither on, no change in hardware settings, below expected input level.
21. Deviation from the mean error of the entire bandwidth, all conversion types.
22. Expected input level = 0 dBm, Mixer level offset = 0.
23. Amplitude error relative to the reference IF bandwidth filter of 40 MHz. Preamplifier mode is set in the on or off position, not Auto.
24. Measured using an attenuator with VSWR performance equal to or better than the Keysight 8490D-020 coaxial attenuator. Peak to average = 0 dB.
25. Measurement referenced to Expected input level setting of –5 dBm.
26. Measurement referenced to Expected input level setting of –3 dBm.
KEYSIGHT [ Keysight Technologies ]
