欢迎访问ic37.com |
会员登录 免费注册
发布采购

474W4220JAA1K 参数 Datasheet PDF下载

474W4220JAA1K图片预览
型号: 474W4220JAA1K
PDF下载: 下载PDF文件 查看货源
内容描述: [Film Capacitor]
分类和应用: 电容器
文件页数/大小: 17 页 / 1570 K
品牌: KEMET [ KEMET CORPORATION ]
 浏览型号474W4220JAA1K的Datasheet PDF文件第5页浏览型号474W4220JAA1K的Datasheet PDF文件第6页浏览型号474W4220JAA1K的Datasheet PDF文件第7页浏览型号474W4220JAA1K的Datasheet PDF文件第8页浏览型号474W4220JAA1K的Datasheet PDF文件第10页浏览型号474W4220JAA1K的Datasheet PDF文件第11页浏览型号474W4220JAA1K的Datasheet PDF文件第12页浏览型号474W4220JAA1K的Datasheet PDF文件第13页  
Metallized Polypropylene Film EMI Suppression Capacitors  
R47 Series, Class X1, 440 VAC, 110ºC (Automotive Grade)  
Soldering Process cont'd  
Wave Soldering Recommendations cont'd  
1. The table indicates the maximum set-up temperature of the soldering process  
Figure 1  
Maximum  
Maximum Preheat  
Peak Soldering  
Temperature  
Temperature  
Dielectric  
Film Material  
Capacitor Capacitor Capacitor Capacitor Capacitor  
Pitch  
Pitch  
Pitch  
Pitch  
Pitch  
≤ꢀ10ꢀmm = 15 mm > 15 mm ≤ꢀ15ꢀmm > 15 mm  
Polyester  
Polypropylene  
Paper  
130°C  
100°C  
130°C  
130°C  
110°C  
130°C  
130°C  
130°C  
140°C  
270°C  
260°C  
270°C  
270°C  
270°C  
270°C  
Polyphenylene  
Sulphide  
150°C  
150°C  
160°C  
270°C  
270°C  
2. The maximum temperature measured inside the capacitor:  
Set the temperature so that inside the element the maximum temperature is below the limit:  
Maximum temperature  
Dielectric Film Material  
measured inside the element  
Polyester  
Polypropylene  
Paper  
160°C  
110°C  
160°C  
160°C  
Polyphenylene  
sulphide  
Temperature monitored inside the capacitor.  
Selective Soldering Recommendations  
Selectiveꢀdipꢀsolderingꢀisꢀaꢀvariationꢀofꢀreflowꢀsoldering.ꢀInꢀthisꢀmethod,ꢀtheꢀprintedꢀcircuitꢀboardꢀwithꢀthrough-holeꢀcomponentsꢀtoꢀbeꢀ  
solderedꢀisꢀpreheatedꢀandꢀtransportedꢀoverꢀtheꢀsolderꢀbathꢀasꢀinꢀnormalꢀflowꢀsolderingꢀwithoutꢀtouchingꢀtheꢀsolder.ꢀWhenꢀtheꢀboardꢀisꢀ  
over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected  
components, and pressed against the lower surface of the board to solder the components.  
Theꢀtemperatureꢀprofileꢀforꢀselectiveꢀsolderingꢀisꢀsimilarꢀtoꢀtheꢀdoubleꢀwaveꢀflowꢀsolderingꢀoutlinedꢀinꢀthisꢀdocument,ꢀhowever, instead  
of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than  
inꢀdoubleꢀwaveꢀflowꢀsoldering,ꢀandꢀgreatꢀcareꢀmustꢀbeꢀtakenꢀsoꢀthatꢀtheꢀpartsꢀareꢀnotꢀoverheated.  
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com  
F3097_R47_X1_440 • 6/9/2016  
9