欢迎访问ic37.com |
会员登录 免费注册
发布采购

GG1236SWUNNRNP-V00-NOCX 参数 Datasheet PDF下载

GG1236SWUNNRNP-V00-NOCX图片预览
型号: GG1236SWUNNRNP-V00-NOCX
PDF下载: 下载PDF文件 查看货源
内容描述: 规格液晶模块 [SPECIFICATIONS FOR LCD MODULE]
分类和应用:
文件页数/大小: 24 页 / 596 K
品牌: JHE [ JEWEL HILL ELECTRONIC ]
 浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第16页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第17页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第18页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第19页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第20页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第21页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第23页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第24页  
JEWEL HILL ELECTRONIC CO.,LTD.  
(1) Make certain that you are grounded when handing LCM.  
(2) Before removing LCM from its packing case or incorporating it into a set, be sure the module and  
your body have the same electric potential.  
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron  
does not leak.  
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground  
potentiality to minimize as much as possible any transmission of electromagnetic waves produced  
sparks coming from the commutator of the motor.  
(5) As far as possible, make the electric potential of your work clothes and that of the workbenches to  
the ground potential.  
(6) To reduce the generation of electro-static discharge, be careful that the air in the work is not too  
dried. A relative humidity of 50%-60% is recommended.  
11.4 PRECAUTIONS FOR OPERATION  
(1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show  
the best contrast.  
(2) Driving the LCD in the voltage above the limit will shorten its lifetime.  
(3) Response time is greatly delayed at temperature below the operating temperature range. However,  
this does not mean the LCD will be out of the order. It will recover when it returns to the specified  
temperature range.  
(4) If the display area is pushed hard during operation, the display will become abnormal. However, it  
will return to normal if it is turned off and then on.  
(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit.  
Therefore, this product must be used and stored within the specified condition of 23±5°C,  
45±20%RH.  
(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.  
11.5 SAFETY  
(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with  
solvents such as acetone and ethanol, which should later be burned.  
(2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off  
thoroughly with soap and water.  
GG1236  
VER: 1.0  
- 21 -  
Issue date: 2005/11/12  
 复制成功!