欢迎访问ic37.com |
会员登录 免费注册
发布采购

GG1236SWUNNRNP-V00-NOCX 参数 Datasheet PDF下载

GG1236SWUNNRNP-V00-NOCX图片预览
型号: GG1236SWUNNRNP-V00-NOCX
PDF下载: 下载PDF文件 查看货源
内容描述: 规格液晶模块 [SPECIFICATIONS FOR LCD MODULE]
分类和应用:
文件页数/大小: 24 页 / 596 K
品牌: JHE [ JEWEL HILL ELECTRONIC ]
 浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第16页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第17页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第18页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第19页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第20页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第22页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第23页浏览型号GG1236SWUNNRNP-V00-NOCX的Datasheet PDF文件第24页  
JEWEL HILL ELECTRONIC CO.,LTD.  
11. Using LCD modules  
11.1 LIQUID CRYSTAL DISPLAY MODULES  
LCD is composed of glass and polarizer. Pay attention to the following items when handling.  
(1) Please keep the temperature within specified range for use and storage. Polarization degradation,  
bubble generation or polarizer peel-off may occur with high temperature and high humidity.  
(2) Do not touch, push or rub the exposed polarizers with anything harder than a HB pencil lead (glass,  
tweezers, etc).  
(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and  
reflectors made of organic substances, which will be damaged by chemicals such as acetone,  
toluene, toluene, ethanol and isopropyl alcohol.  
(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material  
like chamois soaked in petroleum ether. Do not scrub hard to avoid damaging the display surface.  
(5) Wipe off saliva or water drops immediately, contact with water over a long period of time may  
cause deformation or color fading.  
(6) Avoid contacting oil and fats.  
(7) Condensation on the surface and contact with terminals due to cold will damage, stain or  
polarizers. After products are tested at low temperature they must be warmed up in a container  
before coming is contacting with room temperature air.  
(8) Do not put or attach anything on the display area to avoid leaving marks on.  
(9) Do not touch the display with bare hands. This will stain the display area and degrade insulation  
between terminals (some cosmetics are determinate to the polarizers).  
(10)As glass is fragile, it tends to become or chipped during handling especially on the edges. Please  
avoid dropping or jarring.  
11.2 INSTALLING LCD MODULE  
Attend to the following items when installing the LCM.  
(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.  
(2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the  
fitting plate should have enough height to avoid causing stress to the module surface, refer to the  
individual specifications for measurements. The measurement tolerance should be ±0.1mm.  
11.3 ELECTRO-STATIC DISCHARGE CONTROL  
Since this module uses a CMOS LSI, the same careful attention should be paid for electrostatic  
discharge as for an ordinary CMOS IC.  
GG1236  
VER: 1.0  
- 20 -  
Issue date: 2005/11/12  
 复制成功!