DG441, DG442
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
GND to V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+34V
Digital Inputs, V
S
, V
D
(Note 1)
. . . . . . . . (V-) -2V to (V+) + 2V or 30mA, Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . .
30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max)
. . 100mA
Thermal Information
Thermal Resistance (Typical, Note 2)
θ
JA
(°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
150
Maximum Junction Temperature (Plastic Packages) . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(SOIC and TSSOP- Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Signal Voltage Range
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V
(Max)
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max)
Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min)
Input Rise and Fall Time
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤20ns
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S
X
, D
X
or IN
X
exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.
2.
θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
(Dual Supply) Test Conditions: V+ = +15V, V- = -15V, V
IN
= 2.4V, 0.8V, V
ANALOG
= V
S
, V
D
,
Unless Otherwise Specified
TEST CONDITIONS
TEMP
(°C)
MIN
(NOTE 3)
TYP
MAX
UNITS
PARAMETER
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
Turn-OFF Time, t
OFF
DG441
DG442
Charge Injection, Q (Figure 2)
OFF Isolation (Figure 4)
Crosstalk (Channel-to-Channel) (Figure 3)
Source OFF Capacitance, C
S(OFF)
Drain OFF Capacitance, C
D(OFF)
Channel ON Capacitance,
C
D(ON)
+ C
S(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current V
IN
Low, I
IL
Input Current V
IN
High, I
IH
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Drain-Source ON Resistance, r
DS(ON
)
R
L
= 1kΩ, C
L
= 35pF, V
S
=
±10V,
(Figure 1)
+25
-
150
250
ns
+25
-
-
90
110
-1
60
-100
4
4
16
120
210
-
-
-
-
-
-
ns
ns
pC
dB
dB
pF
pF
pF
C
L
= 1nF, V
G
= 0V, R
G
= 0Ω
R
L
= 50Ω, C
L
= 5pF, f = 1MHz
+25
+25
+25
-
-
-
-
-
-
f = 1MHz, V
ANALOG
= 0 (Figure 5)
+25
+25
+25
V
IN
Under Test = 0.8V, All Others = 2.4V
V
IN
Under Test = 2.4V, All Others = 0.8V
Full
Full
-0.5
-0.5
-0.00001
0.00001
0.5
0.5
μA
μA
Full
I
S
= 10mA, V
D
=
±8.5V,
V+ = 13.5V,
V- = -13.5V
V+ = 16.5V, V- = -16.5V, V
D
=
±15.5V,
V
S
= 15.5V
+25
+85
+25
+85
+25
+85
-15
-
-
-0.5
-5
-0.5
-5
-0.5
-10
-
50
-
0.01
-
0.01
-
0.08
-
15
85
100
0.5
5
0.5
5
0.5
10
V
Ω
Ω
nA
nA
nA
nA
nA
nA
Source OFF Leakage Current, I
S(OFF)
Drain OFF Leakage Current, I
D(OFF)
V+ = 16.5V, V- = -16.5V, V
S
= V
D
=
±15.5V
Channel ON Leakage Current,
I
D(ON)
+ I
S(ON)
+25
+85
4
FN3281.10
November 20, 2006
INTERSIL [ INTERSIL CORPORATION ]
