DG408, DG409
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25V
Thermal Resistance (Typical, Note 4)
θ
(°C/W)
JA
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range. . . . . . . . . . -65°C to 125°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC and TSSOP - Lead Tips Only)
90
110
150
Digital Inputs, V , V (Note 3). . . . . .(V-) -2V to (V+) + 2V or 20mA,
S
D
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Signals on S , D , EN or A exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
X
X
X
4. θ is measured with the component mounted on an evaluation PC board in free air.
JA
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, V = 0.8V, V = 2.4V, Unless Otherwise Specified
AL
AH
(NOTE 5)
(NOTE 6)
(NOTE 5)
PARAMETER
TEST CONDITIONS
TEMP (°C)
MIN
TYP
MAX
UNITS
DYNAMIC CHARACTERISTICS
Transition Time, t
(See Figure 1)
Full
25
-
10
-
160
-
250
-
ns
ns
ns
ns
ns
pC
dB
TRANS
Break-Before-Make Interval, t
(See Figure 3)
(See Figure 2)
OPEN
ON(EN)
Enable Turn-ON Time, t
25
115
-
150
225
150
-
Full
Full
25
-
Enable Turn-OFF Time, t
Charge Injection, Q
OFF Isolation
(See Figure 2)
-
105
20
-75
OFF(EN)
C
= 10nF, V = 0V
-
L
S
V
= 0V, R = 1kΩ,
25
-
-
EN
L
f = 100kHz (Note 9)
Logic Input Capacitance, C
f = 1MHz
25
25
-
-
8
3
-
-
pF
pF
IN
Source OFF Capacitance, C
V
= 0V, V = 0V,
S
S(OFF)
EN
f = 1MHz
Drain OFF Capacitance, C
DG408
V
= 0V, V = 0V,
D
D(OFF)
EN
f = 1MHz
25
25
-
-
26
14
-
-
pF
pF
DG409
Drain ON Capacitance, C
DG408
V
= 3V, V = 0V,
D
D(ON)
EN
f = 1MHz, V = 0V or 3V
A
25
25
-
-
37
25
-
-
pF
pF
DG409
DIGITAL INPUT CHARACTERISTICS
Logic Input Current,
Input Voltage High, I
V
= 2.4V, 15V
Full
Full
-10
-10
-
-
10
10
µA
µA
A
AH
Logic Input Current,
Input Voltage Low, I
AL
V
= 0V, 2.4V,
EN
V = 0V
A
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
Full
25
-15
-
40
-
15
100
125
15
V
Ω
Ω
Ω
ANALOG
Drain-Source ON Resistance,
V
= ±10V, I = -10mA
-
-
-
D
S
r
(Note 7)
DS(ON)
Full
25
r
Matching Between Channels,
V
= 10V, -10V (Note 8)
-
DS(ON)
D
∆r
DS(ON)
Source OFF Leakage Current, I
V
V
= 0V, V = ±10V,
= +10V
25
-0.5
-5
-
-
0.5
5
nA
nA
S(OFF)
EN
S
D
Full
FN3283.8
June 13, 2006
4
INTERSIL [ Intersil ]
