80C186EC/188EC, 80L186EC/188EC
DC SPECIFICATIONS (80C186EC/80C188EC)
Symbol
Parameter
Supply Voltage
Min
Max
Units
V
Notes
V
V
V
V
V
V
4.5
5.5
CC
IL
b
Input Low Voltage
0.5
0.7 V
0.3 V
V
CC
a
V
CC
Input High Voltage
0.5
V
IH
CC
e
Output Low Voltage
Output High Voltage
Input Hysteresis on RESIN
0.45
V
I
I
3 mA (Min)
OL
OH
HYR
OL
b
e b
2 mA (Min)
V
0.5
V
CC
OH
0.5
V
s
s
V
g
I
Input Leakage Current for Pins:
AD15:0 (AD7:0, A15:8), READY,
HOLD, RESIN,
15
mA
0
V
LI
IN
CC
CLKIN, TEST/BUSY, NMI, INT7:0,
T0IN, T1IN, P2.7–P2.0, P3.5–P3.0,
DRQ3:0, PEREQ, ERROR
b
b
e
0.7 V
IN
(Note 1)
I
Input Leakage for Pins with Pullups
Active During Reset:
A19:16, LOCK
0.275
5
mA
V
LIU
CC
s
s
V
g
I
I
Output Leakage for Floated Output
Pins
15
mA
0.45
(Note 2)
V
LO
CC
OUT
CC
Supply Current Cold (in RESET)
80C186EC25
80C186EC20
125
100
70
mA
mA
mA
(Notes 3, 7)
(Note 3)
(Note 3)
80C186EC13
I
I
Supply Current in Idle Mode
80C186EC25
80C186EC20
ID
92
76
50
mA
mA
mA
(Notes 4, 7)
(Note 4)
(Note 4)
80C186EC13
Supply Current in Powerdown Mode
80C186EC25
80C186EC20
PD
100
100
100
mA
mA
mA
(Notes 5, 7)
(Note 5)
(Note 5)
80C186EC13
e
e
C
C
Input Pin Capacitance
Output Pin Capacitance
0
0
15
15
pF
pF
T
T
1 MHz
1 MHz (Note 6)
IN
F
F
OUT
NOTES:
1. These pins have an internal pull-up device that is active while RESIN is low and ONCE Mode is not active. Sourcing more
current than specified (on any of these pins) may invoke a factory test mode.
2. Tested by outputs being floated by invoking ONCE Mode or by asserting HOLD.
3. Measured with the device in RESET and at worst case frequency, V , and temperature with ALL outputs loaded as
CC
or GND.
specified in AC Test Conditions, and all floating outputs driven to V
4. Measured with the device in HALT (IDLE Mode active) and at worst case frequency, V , and temperature with ALL
CC
CC
or GND.
5. Measured with the device in HALT (Powerdown Mode active) and at worst case frequency, V , and temperature with
outputs loaded as specified in AC Test Conditions, and all floating outputs driven to V
CC
CC
or GND.
ALL outputs loaded as specified in AC Test Conditions, and all floating outputs driven to V
6. Output Capacitance is the capacitive load of a floating output pin.
CC
a
7. Operating conditions for 25 MHz is 0 C to 70 C, V
e
g
5.0 10%.
§
§
CC
26