欢迎访问ic37.com |
会员登录 免费注册
发布采购

ILC7280CS-3030 参数 Datasheet PDF下载

ILC7280CS-3030图片预览
型号: ILC7280CS-3030
PDF下载: 下载PDF文件 查看货源
内容描述: 与75DB纹波抑制微功耗双150MA CMOS射频LDO稳压器 [MICROPOWER DUAL 150MA CMOS RF LDO REGULATORS WITH 75DB RIPPLE REJECTION]
分类和应用: 稳压器调节器电源电路射频光电二极管输出元件
文件页数/大小: 9 页 / 66 K
品牌: IMPALA [ Impala Linear Corporation ]
 浏览型号ILC7280CS-3030的Datasheet PDF文件第1页浏览型号ILC7280CS-3030的Datasheet PDF文件第2页浏览型号ILC7280CS-3030的Datasheet PDF文件第3页浏览型号ILC7280CS-3030的Datasheet PDF文件第4页浏览型号ILC7280CS-3030的Datasheet PDF文件第6页浏览型号ILC7280CS-3030的Datasheet PDF文件第7页浏览型号ILC7280CS-3030的Datasheet PDF文件第8页浏览型号ILC7280CS-3030的Datasheet PDF文件第9页  
Advance  
Micropower Dual 150mA CMOS RF LDO™ Regulators with 75dB Ripple Rejection  
Electrical Characteristics ILC7280CS  
Unless otherwise specified, all limits are at TA = 25°C; VIN = VO(NOM) + 1V, IOUT = 1mA, COUT = 0.47µF, VS/D = 2V.  
Boldface limits apply over the operating temperature range. (Note 2)  
Parameter  
Symbol  
Conditions  
Min  
2.0  
Typ  
Max Units  
10  
VS/D  
High = Regulator On  
Low = Regulator Off  
Shut Down Input Voltage  
V
0.6  
IO(peak)  
eN  
VOUT > 0.95VO(NOM)  
500  
Peak Output Current (Note 4)  
300  
mA  
Output Noise Voltage (RMS)  
µV  
dB  
BW = 300Hz to 50kHz, CNOISE = 0pF  
60  
60  
freq = 1kHz  
Ripple Rejection  
VO/VIN  
VO(line)  
freq = 10kHz  
freq = 100kHz  
VIN: VO(NOM) + 1V to VO(NOM) + 2V; dVIN/dt  
1V/µS;lo = 150mA  
60  
10  
Dynamic Line Regulation  
=
mV  
40  
20  
IOUT: 0 to 150mA; d(lOUT)/dt = 50A/µs, with  
COUT = 2.2µF  
VO(load)  
Dynamic Load Regulation  
Short Circuit Current  
mV  
mA  
ISC  
VOUT = 0V  
300  
Note1: Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical specifications do not apply  
when operating the device outside of its rated operating conditions.  
Note 2: Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods. Measurements are  
taken at constant junction temperature as close to ambient as possible using low duty pulse testing.  
Note 3: Dropout Voltage is defined as the measured Differential Voltage between input and output voltage, when the output voltage drops 2% below the nominal output  
voltage as VIN is decreased, and approaches VOUT . Nominal output voltage is defined at VIN = VOUT + 1V.  
Note 4: Guaranteed by design  
Impala Linear Corporation  
ILC7280 1.8  
www.impalalinear.com  
(408) 574-3939  
May 2000  
5