IDT29FCT2052AT/BT/CT
FAST CMOS OCTAL REGISTERED TRANSCEIVER
INDUSTRIAL TEMPERATURE RANGE
PIN DESCRIPTION
Name
A
0-7
B
0-7
CPA
CEA
OEB
CPB
CEB
OEA
I/O
I/O
I/O
I
I
I
I
I
I
Description
Eight bidirectional lines carrying the A Register inputs or B Register outputs
Eight bidirectional lines carrying the B Register inputs or A Register outputs
Clock for the A Register. When
CEA
is LOW, data is entered into the A Register on the LOW-to-HIGH transition of the CPA signal.
Clock Enable for the A Register. When
CEA
is LOW, data is entered into the A Register on the LOW-to-HIGH transition of the CPA signal. When
CEA
is HIGH, the A Register holds its contents, regardless of CPA signal transitions.
Output Enable for the A Register. When
OEB
is LOW, the A Register outputs are enabled onto the B
0-7
lines. When
OEB
is HIGH, the B
0-7
outputs
are in the high-impedance state.
Clock for the B Register. When
CEB
is LOW, data is entered into the B Register on the LOW-to-HIGH transition of the CPB signal.
Clock Enable for the B Register. When
CEB
is LOW, data is entered into the B Register on the LOW-to-HIGH transition of the CPB signal. When
CEB
is HIGH, the B Register holds its contents, regardless of CPB signal transitions.
Output Enable for the B Register. When
OEA
is LOW, the B Register outputs are enabled onto the A
0-7
lines. When
OEA
is HIGH, the A
0-7
outputs
are in the high-impedance state.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 5.0V ±5%
Symbol
V
IH
V
IL
I
IH
I
IL
I
OZH
I
OZL
I
I
V
IK
V
H
I
CC
Parameter
Input HIGH Level
Input LOW Level
Input HIGH Current
(4)
Input LOW Current
(4)
High Impedance Output Current
(3-State Output pins)
(4)
Input HIGH Current
(4)
Clamp Diode Voltage
Input Hysteresis
Quiescent Power Supply Current
V
CC
= 3V
V
IN
= GND or V
CC
V
CC
= Max., V
I
= V
CC
(Max.)
V
CC
= Min., I
IN
= –18mA
—
Test Conditions
(1)
Guaranteed Logic HIGH Level
Guaranteed Logic LOW Level
V
CC
= Max.
V
CC
= Max.
V
CC
= Max., V
I
= V
CC
(Max.)
V
I
= 2.7V
V
I
= 0.5V
V
I
= 2.7V
V
I
= 0.5V
Min.
2
—
—
—
—
—
—
—
—
—
Typ.
(2)
—
—
—
—
—
—
—
–0.7
200
0.01
Max.
—
0.8
±1
±1
±1
±1
±1
–1.2
—
1
µA
V
mV
µA
Unit
V
V
µA
µA
µA
OUTPUT DRIVE CHARACTERISTICS
Symbol
I
ODL
I
ODH
V
OH
V
OL
Parameter
Output LOW Current
Output HIGH Current
Output HIGH Voltage
Output LOW Voltage
Test Conditions
(1)
V
CC
= 5V, V
IN
= V
IH
or V
IL
, V
OUT
= 1.5V
(3)
V
CC
= 5V, V
IN
= V
IH
or V
IL
, V
OUT
= 1.5V
(3)
V
CC
= Min
I
OH
= –15mA
V
IN
= V
IH
or V
IL
V
CC
= Min
I
OL
= 12mA
V
IN
= V
IH
or V
IL
Min.
16
-16
2.4
—
Typ.
(2)
48
-48
3.3
0.3
Max.
—
—
—
0.5
Unit
mA
mA
V
V
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. The test limit for this parameter is ±5µA at T
A
= –55°C.
3
IDT [ INTEGRATED DEVICE TECHNOLOGY ]
