IBM0612404GT3B
IBM0612804GT3B
128Mb Double Data Rate Synchronous DRAM
Advance Rev 0.2
Electrical Characteristics & AC Timing for PC266/PC200 - Absolute Specifications
(0 °C ≤ TA ≤ 70 °C; VDDQ = 2.5V ± 0.2V; VDD = 2.5V ± 0.2V, See AC Characteristics) (Part 2 of 3)
PC266A
PC266B
PC200
Min
Symbol
Parameter
Unit Notes
Min
Max
1.25
Min
Max
1.25
Max
1.25
Write command to 1st DQS latching
transition
t
0.75
0.35
0.2
0.75
0.35
0.2
0.75
0.35
0.2
t
t
t
1-4
1-4
1-4
DQSS
CK
CK
CK
t
DQS input low (high) pulse width (write cycle)
DQSL,H
DQS falling edge to CK setup time (write
cycle)
t
DSS
DQS falling edge hold time from CK (write
cycle)
t
0.2
0.2
0.2
t
1-4
1-4
DSH
CK
t
Mode register set command cycle time
Write preamble setup time
Write postamble
14
0
15
0
16
0
ns
MRD
t
ns 1-4, 7
WPRES
t
0.40
0.25
0.60
0.40
0.25
0.60
0.40
0.25
0.60
t
t
1-4, 6
1-4
WPST
WPRE
CK
CK
t
Write preamble
2-4,
ns 11,13,
14
Address and control input hold time
(fast slew rate)
t
0.9
0.9
0.9
0.9
1.1
1.1
IH
2-4,
ns 11,13,
14
Address and control input setup time
(fast slew rate)
t
IS
Address and control input hold time
(slow slew rate)
2-4,
ns
t
1.0
1.0
1.0
1.0
1.1
1.1
IH
12-14
Address and control input setup time
(slow slew rate)
2-4,
ns
t
IS
12-14
t
Input pulse width
Read preamble
Read postamble
2.2
0.9
2.2
0.9
ns 2-4, 14
IPW
t
1.1
1.1
0.9
1.1
t
t
1-4
1-4
RPRE
CK
CK
t
0.40
0.60
0.40
0.60
0.40
0.60
RPST
1. Input slew rate = 1V/ns
2. The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference level for
signals other than CK/CK, is V
REF.
3. Inputs are not recognized as valid until V
stabilizes.
REF
4. The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (Note 3) is V
.
TT
5. t and t transitions occur in the same access time windows as valid data transitions. These parameters are not referred to a
HZ
LZ
specific voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ).
6. The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system
performance (bus turnaround) degrades accordingly.
7. The specific requirement is that DQS be valid (high, low, or some point on a valid transition) on or before this CK edge. A valid tran-
sition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in
progress on the bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH,
LOW, or transitioning from high to low at this time, depending on t
.
DQSS
8. A maximum of eight Autorefresh commands can be posted to any given DDR SDRAM device.
9. QFC is enabled as soon as possible after the rising CK edge that registers the Write command.
10. QFC is disabled as soon as possible after the last valid DQS edge transitions Low.
11. For command/address input slew rate ≥ 1.0V/ns. Slew rate is measured between V (AC) and V (AC).
OH
OL
12. For command/address input slew rate ≥ 0.5V/ns and < 1.0V/ns. Slew rate is measured between V (AC) and V (AC).
OH
OL
13. CK/CK slew rates are ≥ 1.0V/ns.
14. These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by
design or tester correlation.
15. The specified timing is guaranteed assuming QFC is connected to a test load consisting of 20pF to ground and a pull up resistor of
150 ohms to V
.
ddq
©IBM Corporation. All rights reserved.
Use is further subject to the provisions at the end of this document.
06K0566.F39350
5/00
Page 60 of 79
IBM [ IBM ]
