Global Mixed-mode Technology Inc.
G924
Absolute Maximum Ratings
VIN to GND.………………………………-0.3V to +6.5V
Output Short-Circuit Duration…….….……….…Infinite
Operating Temperature Range…….....-40°C to +85°C
Junction Temperature………………...………+150°C
θJA(1)….…..…………….……….…..…..240°C/Watt
Storage Temperature Range……….-65°C to +150°C
Reflow Temperature (soldering, 10sec)…..…….260°C
SHDNto GND……..………....….….-0.3V to VIN+0.3V
OUT to GND………………………-0.3V to (VIN + 0.3V)
Continuous Power Dissipation (TA = +25°C)
SOT-23-5………..…………..……….……….…520mW
Note (1): See Recommended Minimum Footprint
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Electrical Characteristics
(VIN =5V, V SHDN =VIN, TA =TJ =25°C, unless otherwise noted.) (Note 1)
PARAMETER
Input Voltage (Note 2)
SYMBOL
CONDITION
MIN TYP MAX UNIT
VIN
2.5
-2
---
---
---
---
---
5.5
2
V
V
OUT≥2.50V, IOUT=1mA
Output Voltage Accuracy
VOUT
%
2.50V>VOUT≥1.80V, IOUT=1mA
1.80V>VOUT≥1.20V, IOUT=1mA
-3
3
-4
4
Maximum Output Current
Current Limit (Note 3)
Short Circuit Current
Ground Pin Current
300
---
---
---
---
mA
mA
mA
µA
ILIM
Isc
IQ
400 550
---
280
90
---
---
---
---
---
---
---
---
---
VOUT=1.50V
1.36 ---
1.10 ---
0.58 ---
0.41 ---
0.36 ---
0.25 ---
0.24 ---
0.06 ---
VOUT=1.80V
VOUT=2.50V
VOUT=3.00V
VOUT=3.30V
VOUT=4.75V
VOUT=5.00V
Dropout Voltage (Note 4)
VDROP IOUT =300mA
V
Line Regulation
Load Regulation
Ripple Rejection
∆VLNR VIN=VOUT+0.1V,to 5.5V IOUT=10mA
∆VLDR
OUT = 10mA to 300mA
PSRR F=1kHz, 0.45VP-P, IOUT=10mA
%/V
I
---
---
0.02 --- %/mA
53
28
---
dB
Output Voltage Noise
(10Hz to 100kHz)
en
COUT = 1µF, IOUT = 1mA, CBYP = 10nF
---
--- µVRMS
SHUTDOWN
VIH
Regulator enabled
Regulator shutdown
1.5
---
---
---
---
V
0.4
SHDN Input Threshold
VIL
I
SHDN
V SHDN = VIN
TA = +25°C
TA = +25°C
SHDN Input Bias Current
--- 0.003
1
1
µA
µA
Shutdown Supply Current
THERMAL PROTECTION
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
IQSHDN VOUT = 0V
---
0.2
TSHDN
---
---
145
25
---
---
°C
°C
∆TSHDN
Note 1: Limits is 100% production tested at TA= +25°C. Low duty pulse techniques are used during test to
maintain junction temperature as close to ambient as possible.
Note 2: Guaranteed by line regulation test.
Note 3: Not tested. For design purposes, the current limit should be considered 400mA minimum.
Note 4: The dropout voltage is defined as (VIN-VOUT) when VOUT is 100mV below the target value of VOUT. The per-
formance of every G924 part, see “Typical Performance Characteristics”.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 0.2 Preliminary
Oct 01, 2004
3