欢迎访问ic37.com |
会员登录 免费注册
发布采购

FT232HL 参数 Datasheet PDF下载

FT232HL图片预览
型号: FT232HL
PDF下载: 下载PDF文件 查看货源
内容描述: FT232H单通道HI -SPEED USB ​​TO多用途UART / FIFO IC [FT232H Single Channel Hi-Speed USB to Multipurpose UART/FIFO IC]
分类和应用: 先进先出芯片
文件页数/大小: 65 页 / 1621 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号FT232HL的Datasheet PDF文件第25页浏览型号FT232HL的Datasheet PDF文件第26页浏览型号FT232HL的Datasheet PDF文件第27页浏览型号FT232HL的Datasheet PDF文件第28页浏览型号FT232HL的Datasheet PDF文件第30页浏览型号FT232HL的Datasheet PDF文件第31页浏览型号FT232HL的Datasheet PDF文件第32页浏览型号FT232HL的Datasheet PDF文件第33页  
Document No.: FT_000288
FT232H SINGLE CHANNEL HI-SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 1.3
Clearance No.: FTDI #199
4.6 FT1248 Interface Mode Description
The FT232H supports a half duplex FT1248 Interface that provides a flexible data communication and
high performance interface between the FT232H as a FT1248 slave and an external FT1248 master. The
FT1248 protocol is a dynamic bi-directional data bus interface that can be configured as 1, 2, 4, or 8-bits
wide.
FPGA (FT1248 Master)
SCLK
MIOSIO
FT232H (FT1248 Slave)
SCLK
[7:0]
MIOSIO
MISO
SS#
MISO
SS#
Figure 4.7 FT1248 Bus with Single Master and Slave.
In the FT1248 there are 3 distinct phases:
While SS_n is inactive, the FT1248 reflects the status of the write buffer and read buffers on the
MIOSIO[0] and MISO wires respectively. Additionally, the FT1248 slave block supports multiple slave
devices where a master can communicate with multiple FT1248 slave devices. When the slave is sharing
buses with other FT1248 slave devices, the write and read buffer status cannot be reflected on the
MIOSIO[0] and MISO wires during SS_n inactivity as this would cause bus contention. Therefore, it is
possible for the user to select whether they wish to have the buffer status switched on or off during
inactivity. When SS_n is active a command/bus size phase occurs first. Following the command phase is
the data phase, for each data byte transferred the FT1248 slave drives an ACK/NAK status onto the MISO
wire. The master can send multiple data bytes so long as SS_n is active, if a unsuccessful data transfer
occurs, i.e. a NAK happens on the MISO wire then the master should immediately abort the transfer by
de-asserting SS_n.
CLK
SCLK
READ
SS_n
WRITE
WRITE DATA
BUS TURNAROUND
MIOSIO[0]
TXE#
CMD
RDATA0
RDATA1
RDATA2
TXE#
CMD
WDATA 0
WDATA 1
TXE#
MISO
RXF#
STATUS
STATUS
STATUS
RXF#
STATUS
STATUS
RXF#
Figure 4.8: FT1248 Basic Waveform Protocol.
Section 4.6.2 illustrates the FT1248 write and read protocol operating in 1-bit mode. For details regarding
2-bit, 4-bit and 8-bit modes, please refer to application note AN_167_FT1248 Parallel Serial Interface
Basics available at
Copyright © 2011 Future Technology Devices International Limited
29