ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics
Characteristics noted under conditions 6.0 V
≤
V
PWR
≤
20 V, 3.0 V
≤
V
DD
≤
5.5 V, - 40°C
≤
T
A
≤
125°C, GND = 0 V unless
otherwise noted. Typical values noted reflect the approximate parameter means at T
A
= 25°C under nominal conditions unless
otherwise noted.
Characteristic
POWER INPUTS
Battery Supply Voltage Range
Fully Operational
Extended mode
Battery Clamp Voltage
V
PWR
Operating Supply Current
Outputs commanded ON,
HS[0 : 3] open,
IN[0:3] > V
IH
V
PW
R
Supply Current
Outputs commanded OFF, OFF Open-load Detection Disabled, HS[0 : 3]
shorted to the ground with V
DD
= 5.5 V
WAKE > V
IH
or RST > V
IH
and IN[0:3] < V
IL
Sleep State Supply Current
V
PWR
= 12V, RST = WAKE = IN[0:3] < V
IL
, HS[0 : 3] shorted to the ground
T
A
= 25°C
T
A
= 85°C
V
DD
Supply Voltage
V
DD
Supply Current at V
DD
= 5.5 V
No SPI Communication
8.0 MHz SPI Communication
V
DD
Sleep State Current at V
DD
= 5.5 V
Over-voltage Shutdown Threshold
Over-voltage Shutdown Hysteresis
Under-voltage Shutdown Threshold
Symbol
Min
Typ
Max
Unit
V
PWR
6.0
4.0
V
PWR(CLAMP
)
V
–
–
47
20
28
53
V
mA
–
6.5
20
mA
–
6.5
8.0
μA
–
–
1.0
–
–
5.0
30
5.5
V
mA
–
–
1.6
5.0
–
32
0.8
3.9
-
4.1
2.5
2.2
–
5.0
36
1.5
4.3
0.9
4.5
2.8
μA
V
V
V
V
PWR(UV)
V
V
41
I
PWR(ON)
I
PWR(SBY)
I
PWR(SLEEP)
V
DD(ON)
I
DD(ON)
3.0
I
DD(SLEEP)
V
PWR(OV)
V
PWR(OVHYS
)
–
28
0.2
3.3
0.5
3.4
2.2
V
PWR(UV)
V
SUPPLY(PO
R)
V
PWR
and V
DD
Power on Reset Threshold
Recovery Under-voltage Threshold
V
DD
Supply Failure Threshold ( for
V
PWR
> V
PWR(UV)
)
Vpwr(UV)_U
P
V
DD(FAIL)
Notes
10. In extended mode, the functionality is guaranteed but not the electrical parameters. From 4.0 V to 6.0 V voltage range, the device is only
protected with the thermal shutdown detection.
11. Measured with the outputs open.
12. Typical value guaranteed per design.
13. Output will automatically recover with time limited autoretry to instructed state when V
PWR
voltage is restored to normal as long as the
V
PWR
degradation level did not go below the under-voltage power-ON reset threshold. This applies to all internal device logic that is
supplied by V
PWR
and assumes that the external V
DD
supply is within specification.
10XS3412
8
Analog Integrated Circuit Device Data
Freescale Semiconductor
FREESCALE [ FREESCALE SEMICONDUCTOR, INC ]
