Absolute Maximum Ratings(Note 5)
Recommended Operating
Conditions
Storage Temperature (TSTG
)
−65°C to +150°C
Maximum Junction Temperature
(TJ)
Case Temperature (TC)
Commercial
+150°C
−7.0V to +0.5V
−0.5V to +6.0V
0°C to +85°C
−40°C to +85°C
−5.7V to −4.2V
+4.5V to +5.5V
VEE Pin Potential to Ground Pin
VTTL Pin Potential to Ground Pin
ECL Input Voltage (DC)
ECL Output Current
Industrial
ECL Supply Voltage (VEE
)
VEE to +0.5V
TTL Supply Voltage (VTTL
)
(DC Output HIGH)
−50 mA
TTL Input Voltage (Note 7)
TTL Input Current (Note 7)
Voltage Applied to Output
in HIGH State
−0.5V to +7.0V
−30 mA to +5.0 mA
Note 5: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
3-STATE Output
−0.5V to +5.5V
Current Applied to TTL
Output in LOW State (Max)
ESD (Note 6)
twice the Rated IOL (mA)
Note 6: ESD testing conforms to MIL-STD-883, Method 3015.
Note 7: Either voltage limit or current limit is sufficient to protect inputs.
≥2000V
Commercial Version
TTL-to-ECL DC Electrical Characteristics (Note 8)
V
EE = −4.2V to −5.7V, GND = 0V, TC = 0°C to +85°C, VTTL = +4.5V to +5.5V
Symbol
Parameter
Min
Typ
−955
−1705
Max
Units
mV
Conditions
VOH
VOL
Output HIGH Voltage
−1025
−1830
−870
V
IN = VIH(Max) or VIL(Min)
Output LOW Voltage
Cutoff Voltage
−1620
mV
Loading with 50Ω to − 2V
OE and LE Low, DIR High
−2000
−1950
mV
V
IN = VIH(Max) or VIL(Min),
Loading with 50Ω to −2V
VOHC
Output HIGH Voltage
Corner Point High
Output LOW Voltage
Corner Point Low
Input HIGH Voltage
Input LOW Voltage
Input HIGH Current
Input HIGH Current
Breakdown (I/O)
−1035
mV
mV
V
IN = VIH(Min) or VIL(Max)
VOLC
Loading with 50Ω to −2V
−1610
VIH
VIL
2.0
0
5.0
0.8
5.0
V
V
Over VTTL, VEE, TC Range
Over VTTL, VEE, TC Range
IIH
µA
V
V
V
IN = +2.7V
IN = 5.5V
IN = +0.5V
IBVIT
0.5
mA
mA
V
IIL
Input LOW Current
Input Clamp
−1.0
−1.2
−99
VFCD
I
IN = −18 mA
Diode Voltage
IEE
VEE Supply Current
−50
−90
LE Low, OE and DIR HIGH
Inputs Open
IEEZ
VEE Supply Current
−159
LE and OE Low, Dir HIGH
Inputs Open
Note 8: The specified limits represent the “worst case” value for the parameter. Since these values normally occur at the temperature extremes, additional
noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are cho-
sen to guarantee operation under “worst case” conditions.
www.fairchildsemi.com
4