欢迎访问ic37.com |
会员登录 免费注册
发布采购

ES29F320FT-70WC 参数 Datasheet PDF下载

ES29F320FT-70WC图片预览
型号: ES29F320FT-70WC
PDF下载: 下载PDF文件 查看货源
内容描述: 16兆( 2M ×8 / 1M ×16 )的CMOS 3.0伏只,引导扇区闪存 [16Mbit(2M x 8/1M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory]
分类和应用: 闪存
文件页数/大小: 53 页 / 700 K
品牌: EXCELSEMI [ EXCEL SEMICONDUCTOR INC. ]
 浏览型号ES29F320FT-70WC的Datasheet PDF文件第24页浏览型号ES29F320FT-70WC的Datasheet PDF文件第25页浏览型号ES29F320FT-70WC的Datasheet PDF文件第26页浏览型号ES29F320FT-70WC的Datasheet PDF文件第27页浏览型号ES29F320FT-70WC的Datasheet PDF文件第29页浏览型号ES29F320FT-70WC的Datasheet PDF文件第30页浏览型号ES29F320FT-70WC的Datasheet PDF文件第31页浏览型号ES29F320FT-70WC的Datasheet PDF文件第32页  
E S I  
E S I  
Excel Semiconductor inc.  
DQ5 ( EXCEEDED TIMING LIMITS )  
If additional sectors are selected for erasure, the  
entire time-out also applies after each additional  
sector erase command. When the time-out period is  
complete, DQ3 switches from a “0” to a”1”. If the  
time between additional sector erase commands  
from the system can be assumed to be less than  
50us, the system need not monitor DQ3. See also  
the Sector Erase Command Sequence section. After  
the sector erase command is written, the system  
should read the status of DQ7 (Data# Polling) or  
DQ6 (Toggle Bit I) to ensure that the device has  
accepted the command sequence, and then read  
DQ3. If DQ3 is “1”, the Embedded Erase algorithm  
has begun; all further commands (except Erase Sus-  
pend) are ignored until the erasure operation is com-  
plete. If DQ3 is “0”, the device will accept additional  
sector erase commands. To ensure the command  
has been accepted, the system software should  
check the status of DQ3 prior to and following each  
subsequent sector erase command. If DQ3 is high  
on the second status check, the last command might  
not have been accepted. In Table 10, DQ3 status  
operation is well defined and summarized with other  
status bits, DQ7, DQ6, DQ5, and DQ2.  
DQ5 indicates whether the program or erase time  
has exceeded a specified internal pulse count limit.  
Under these conditions DQ5 produces a “1”, indi-  
cating that the program or erase cycle was not suc-  
cessfully completed. The device may output a “1”  
on DQ5 if the system tries to program a “1” to a  
location that was previously programmed to “0”  
Only an erase operation can change a “0” back to a  
“1”. Under this condition, the device halts the opera-  
tion, and when the timing limit has been exceeded,  
DQ5 produces a ”1”. Under both these conditions,  
the system must write the reset command to return  
to the read mode.  
DQ3 ( SECTOR ERASE TIMER )  
After writing a sector erase command sequence,  
the system may read DQ3 to determine whether or  
not erasure has begun. (The sector erase time  
does not apply to the chip erase command.)  
Table 10. Write Operation Status  
DQ7  
DQ5  
(Note 1)  
DQ3  
DQ2  
(Note 2)  
RY/  
BY#  
Status  
DQ6  
(Note 2)  
DQ7#  
0
Embedded Program Algorithm  
Embedded Erase Algorithm  
Toggle  
Toggle  
0
0
N/A  
No toggle  
0
0
Standard  
Mode  
1
Toggle  
Toggle  
Erase Suspended  
Sector  
1
No toggle  
0
N/A  
1
Erase-Suspend-  
Read  
Erase Sus-  
pend Mode  
Non-Erase  
Suspended Sector  
Data  
Data  
Data  
0
Data  
N/A  
Data  
N/A  
1
0
Erase-Suspend-Program  
DQ7#  
Toggle  
Notes :  
1. DQ5 switches to “1” when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to the  
section on DQ5 for more information.  
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.  
28  
Rev. 0B January 5 , 2006  
ES29LV160E  
 复制成功!