E S I
E S I
Excel Semiconductor inc.
Erase Suspend mode. Toggle Bit I may be read at
any address, and is valid after the rising edge of the
final WE# pulse in the command sequence ( prior to
the program or erase operation), and during the sec-
tor erase time-out. During an Embedded Program or
Erase algorithm operation, successive read cycles to
any address cause DQ6 to toggle. The system may
use either OE# or CE# to control the read cycles.
When the operation is complete, DQ6 stops tog-
gling.
START
Read DQ7-DQ0
Addr = VA
Yes
DQ7 = Data ?
No
No
DQ5 = 1 ?
The system can use DQ6 and DQ2 together to
determine whether a sector is actively erasing or is
erase-suspended. When the device is actively eras-
ing (that is, the Embedded Erase algorithm is in
progress), DQ6 toggles. When the device enters the
Erase Suspend mode, DQ6 stops toggling. How-
ever, the system must also use DQ2 to determine
which sectors are erasing or erase-suspended.
Alternatively, the system can use DQ7(see the sub-
section on DQ7:Data# Polling). DQ6 also toggles
during the erase-suspend-program mode, and stops
toggling once the Embedded Program algorithm is
complete.
Yes
Read DQ7-DQ0
Addr = VA
Yes
DQ7 = Data ?
No
FAIL
PASS
Notes:
1. VA = Valid address for programming. During a sector erase
operation, a valid address is any sector address within the
sector being erased. During chip erase, a valid address in
any non-protected sector address.
Table 10 shows the outputs for Toggle Bit I on DQ6.
Fig. 10 shows the toggle bit algorithm. Fig. 23 in the
“AC Characteristics” section shows the toggle bit
timing diagrams. Fig. 24 shows the differences
between DQ2 and DQ6 in graphical form. See also
the subsection on DQ2 : (Toggle Bit II).
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5
Figure 9. Data# Polling Algorithm
Toggling on the Protected Sectors
After an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6 tog-
gles for approximately 1.8us, then returns to reading
array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unpro-
tected sectors, and ignores the selected sectors that
are protected. If a program address falls within a
protected sector, DQ6 toggles for approximately
250ns after the program command sequence is writ-
ten, then returns to reading array data.
RY/BY# ( READY/BUSY# )
The RY/BY# is a dedicated, open-drain output pin
which indicates whether an Embedded Algorithm is
in progress or complete. The RY/BY# status is valid
after the rising edge of the final WE# pulse in the
command sequence. Since RY/BY# is an open-
drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc. If
the output is low (Busy), the device is actively eras-
ing or programming. (This includes programming in
the Erase Suspend mode.) If the output is high
(Ready), the device is in the read mode, the
standby mode, or in the erase-suspend-read mode.
Table 10 shows the outputs for RY/BY#.
DQ2 ( TOGGLE BIT II )
The “Toggle Bit II” on DQ2, when used with DQ6,
indicates whether a particular sector is actively eras-
ing (that is, the Embedded Erase algorithm is in
progress), or whether that sector is erase-sus-
pended. Toggle Bit II is valid after the rising edge of
the final WE# pulse in the command sequence DQ2
DQ6 ( TOGGLE BIT I )
Toggle Bit I on DQ6 indicates whether an Embed-
ded Program or Erase algorithm is in progress or
complete, or whether the device has entered the
26
Rev. 0B January 5 , 2006
ES29LV160E
EXCELSEMI [ EXCEL SEMICONDUCTOR INC. ]
