ESMT
F49L320UA/F49L320BA
Operation Temperature Condition -40°C~85°C
DQ2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
exceeded the specified limits(internal pulse count). Under
these conditions DQ5 will produce a "1". This time-out
condition indicates that the program or erase cycle was not
successfully completed. Data Polling and Toggle Bit are the
only operating functions of the device under this condition.
If this time-out condition occurs during sector erase
operation, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other sectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence. This
allows the system to continue to use the other active
sectors in the device.
system may use either
or
to control the read
CE
OE
cycles.) But DQ2 cannot distinguish whether the sector is
actively erasing or is erase-suspended.
DQ6, by comparison, indicates whether the device is
actively erasing, or whether is in erase-suspended, but
cannot distinguish which sectors are selected for erasure.
Thus, both status bits are required for sector and mode
information. Refer to Table 7 to compare outputs for DQ2
and DQ6.
Figure 20 shows the toggle bit algorithm in flowchart form.
See also the DQ6: Toggle Bit I subsection. Figure 22
shows the toggle bit timing diagram. Figure 25 shows the
differences between DQ2 and DQ6 in graphical form.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or
combination of sectors are bad.
If this time-out condition occurs during the programming
operation, it specifies that the sector containing that byte is
bad and this sector may not be reused, however other
sectors are still functional and can be reused.
Reading Toggle Bits DQ6/ DQ2
Refer to Figure 20 for the following discussion. Whenever
the system initially begins reading toggle bit status, it must
read DQ7–DQ0 at least twice in a row to determine
whether a toggle bit is toggling. Typically, the system would
note and store the value of the toggle bit after the first read.
After the second read, the system would compare the new
value of the toggle bit with the first. If the toggle bit is not
toggling, the device has completed the program or erase
operation. The system can read array data on DQ7–DQ0
on the following read cycle.
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please note
that this is not a device failure condition since the device
was incorrectly used.
DQ3:Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer does
not apply to the chip erase command.) If additional sectors
are selected for erasure, the entire timeout also applies
after each additional sector erase command.
When the time-out is complete, DQ3 switches from “ 0” to
“ 1.” If the time between additional sector erase commands
from the system can be assumed to be less than 50 µ s, the
system need not monitor DQ3.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system
should note whether the value of DQ5 is high (see the
section on DQ5). If it is, the system should then determine
again whether the toggle bit is toggling, since the toggle bit
may have stopped toggling just as DQ5 went high. If the
toggle bit is no longer toggling, the device has successfully
completed the program or erase operation. If it is still
toggling, the device did not completed the operation
successfully, and the system must write the reset
command to return to reading array data.
When the sector erase command sequence is written, the
system should read the status on DQ7 (Data Polling) or
DQ6 (Toggle Bit I) to ensure the device has accepted the
command sequence, and then read DQ3. If DQ3 is “ 1”, the
internally controlled erase cycle has begun; all further
commands (except Erase Suspend) are ignored until the
erase operation is complete.
The remaining scenario is that the system initially
determines that the toggle bit is toggling and DQ5 has not
gone high. The system may continue to monitor the toggle
bit and DQ5 through successive read cycles, determining
the status as described earlier. Alternatively, it may choose
to perform other system tasks. In this case, the system
must start at the beginning of the algorithm when it returns
to determine the status of the operation.
If DQ3 is “ 0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status of
DQ3 prior to and following each subsequent sector erase
command. If DQ3 is high on the second status check, the
last command might not have been accepted. Table 7
shows the outputs for DQ3.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
Elite Semiconductor Memory Technology Inc.
Publication Date : Sep. 2008
Revision: 1.1
19/55
ESMT [ ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. ]
