欢迎访问ic37.com |
会员登录 免费注册
发布采购

EM3027_13 参数 Datasheet PDF下载

EM3027_13图片预览
型号: EM3027_13
PDF下载: 下载PDF文件 查看货源
内容描述: 实时时钟,带有I2C或SPI ,晶体温度补偿,电池切换和涓流充电器 [Real Time Clock with I2C or SPI, Crystal Temperature Compensation, Battery Switchover and Trickle Charger]
分类和应用: 晶体电池温度补偿时钟
文件页数/大小: 28 页 / 1086 K
品牌: EMMICRO [ EM MICROELECTRONIC - MARIN SA ]
 浏览型号EM3027_13的Datasheet PDF文件第14页浏览型号EM3027_13的Datasheet PDF文件第15页浏览型号EM3027_13的Datasheet PDF文件第16页浏览型号EM3027_13的Datasheet PDF文件第17页浏览型号EM3027_13的Datasheet PDF文件第19页浏览型号EM3027_13的Datasheet PDF文件第20页浏览型号EM3027_13的Datasheet PDF文件第21页浏览型号EM3027_13的Datasheet PDF文件第22页  
EM3027  
8.7.2  
Clock Output  
Output clock frequency is selected by FD1, FD0 bits in EEctrl register.  
FD1  
0
FD0  
0
Select Clock Output  
Description  
From crystal oscillator, without  
32.768 kHz  
frequency compensation  
0
1
1
1
0
1
1024 Hz  
32 Hz  
1 Hz  
With frequency compensation  
Table 12: Output Clock frequency selection  
8.7.3  
Configuration Registers  
All the configuration data from EEPROM (i.e. EEctrl, XTalOffset, Qcoef, TurnOver, EEData) is hold in configuration  
registers.  
Data from EEPROM is loaded to these registers during power-up sequence and is refreshed each hour, if ‘Configuration  
Registers refresh’ feature is enabled (EERefOn = ‘1’).  
Regular refresh of Configuration Registers prevents their content to be corrupted by strongly polluted electrical environment  
(EMC problems, disturbed power supply, etc.).  
It is recommended to enable ‘Configuration Registers refresh’ feature.  
8.7.4  
EEPROM User Memory  
Two bytes of the memory are dedicated for the application (addresses 0x28 and 0x29).  
8.8  
RAM User Memory  
RAM user memory size is 8 bytes (addresses 0x38 to 0x3F). The state of the RAM data after power-up is undefined.  
8.9  
Status Register  
The purpose of EEBusy bit is to inform the user about current status of the EEPROM operations.  
EEBusy – status of EEPROM controller (if EEBusy = ‘1’, then Configuration Registers refresh or EEPROM write is in  
progress)  
The purpose of the following status bits is to record status of power supply voltage and Self-Recovery system/System reset  
behaviour.  
PON  
status of Power-ON  
VLOW1 status of Vlow1 voltage detection  
VLOW2 status of Vlow2 voltage detection  
SR  
status of the Self-Recovery system/System reset  
If one of these status bits is set, it can be cleared only by writing ‘0’, there is no automatic reset if the set condition  
disappears.  
8.10 Interrupts  
There are five interrupt sources which can output an interrupt on (INT and/or IRQ/CLKOUT) pins. The request  
is generated when at least one of IRQflags goes to ‘1’ (OR function).  
AF  
TF  
interrupt is provided when Watch time reaches Alarm time settings and comparison is enabled  
interrupt is provided when Timer reaches ZERO  
V1F  
V2F  
SRF  
interrupt is provided when supply voltage is below Vlow1 (when VLOW1 status bit is set)  
interrupt is provided when supply voltage is below Vlow2 (when VLOW2 status bit is set)  
interrupt is provided when Self-Recovery system invoked internal reset (when SR status bit is set)  
Each interrupt source has its own interrupt enable (AIntE, TIntE, V1IntE, V2IntE, SRIntE). When the interrupt enable is ‘1’  
then the appropriate interrupt source is enabled.  
18  
www.emmicroelectronic.com  
Copyright 2013, EM Microelectronic-Marin SA  
3027-DS.doc, Version 8.0, 25-Jan-13