EM78P510N
8-Bit Microcontrollers
Table 1 (d) SDIP-32/SOP-32
Pin
Pin No. I/O Type
Description
5-bit bidirectional I/O pins.
P73 is pin-shared with SEG15.
P74 is pin-shared with external Interrupt 0 or SEG18.
P75 is pin-shared with external Interrupt 1 or T1OUT or PWM1.
P76 is pin-shared with external Interrupt 2 or T1CK.
P77 is pin-shared with external Interrupt 3 or T1CAP.
P73,
P74~P77 28~31
25,
I/O
2-bit bidirectional I/O pins.
P81 is pin-shared with RESET pin.
P81//RESET
P84/VREF
7
8
I/O
I/O
I/O
P83 can be used as COM7 or Interrupt 9 or AD7 input.(for EM78P510NAK/M
use only)
P84 is pin-shared with A/D reference input pin.
8-bit bidirectional I/O pins.
P90 is pin-shared with AD3 input or PWM2.
P91 is pin-shared with AD2 input or BUZ.
P92 ~P93 are pin-shared with AD1 ~ AD0 input, respectively.
P90~P97 23~30
PA3~PA7 17~21
P94 ~P97 are pin-shared with COM3 ~ COM0, respectively.
5-bit bidirectional I/O pins.
PA3 is pin-shared with SEG3 (for EM78P510NK/M only)
PA4 is pin-shared with SEG4 or SPI SI pin.
PA5 is pin-shared with SEG5 or SPI SO pin.
PA6 is pin-shared with SEG6 or SPI SCK pin.
PA7 is pin-shared with SEG7 or SPI /SS pin.
5-bit bidirectional I/O pins.
PB0 is pin-shared with SEG8 or external Interrupt 4 or AD9 input.
PB1 is pin-shared with SEG9 or external Interrupt 5 or AD10 input.
PB2 is pin-shared with SEG10 or external Interrupt 6 or AD11 input.
PB3 is pin-shared with SEG11 or external Interrupt 7.
PB4 is pin-shared with SEG16 or UART RX pin.
22~24,
26~27
PB0~PB2
PB4~PB5
I/O
PB5 is pin-shared with SEG17 or UART TX pin.
2-bit bidirectional I/O pins.
PC2 ~PC3 are pin-shared with Xin ~ Xout, respectively.
PC2~PC3
OSCI
5~6
3
I/O
I
Crystal mode: crystal input
RC mode: pull-high resistor
PLL mode: connect 0.01µF capacitance to GND.
Connect 0.01µF capacitor to GND and code option select PLL mode when
high oscillator is not used.
Crystal mode: crystal output
OSCO
2
O
RC mode: instruction clock output
PLL mode: instruction clock output
Test
Xin
45
5
I
I
Test signal import pin (must be connected to VDD)
Crystal mode: input pin for sub-oscillator. Connect to a 32.768kHz crystal.
RC mode: pull-high resistor
Xout
6
O
I
Crystal mode: connect to a 32.768kHz crystal.
Input pin with Schmitt Trigger. If this pin remains at logic low, the controller
will also remain in reset condition.
/RESET
7
VDD
VSS
32
1
I
I
Power supply pin
System ground pin
10 •
Product Specification (V0.9) 09.12.2006
(This specification is subject to change without further notice)
ELAN [ ELAN MICROELECTRONICS CORP ]
