EDD5104ADTA-E, EDD5108ADTA-E, EDD5116ADTA-E
DC Characteristics 1 (TA = 0 to +70°C, VDD, VDDQ = 2.5V ± 0.2V, VSS, VSSQ = 0V)
max.
Parameter
Symbol
IDD0
Grade
× 4
× 8
× 16
Unit
mA
Test condition
Notes
1, 2, 9
Operating current (ACT-
PRE)
-6B
-7A, -7B
150
135
150
135
150
135
CKE ≥ VIH,
tRC = tRC (min.)
CKE ≥ VIH, BL = 4,
Operating current
(ACT-READ-PRE)
-6B
-7A, -7B
190
170
200
175
210
180
IDD1
mA
CL = 2.5,
1, 2, 5
tRC = tRC (min.)
Idle power down standby
current
Floating idle standby
current
IDD2P
IDD2F
3
3
3
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
CKE ≤ VIL
4
-6B
30
25
30
25
30
25
CKE ≥ VIH, /CS ≥ VIH,
DQ, DQS, DM = VREF
CKE ≥ VIH, /CS ≥ VIH,
DQ, DQS, DM = VREF
4, 5
-7A, -7B
Quiet idle standby current IDD2Q
20
20
20
4, 10
3
Active power down
IDD3P
20
20
20
CKE ≤ VIL
standby current
-6B
-7A, -7B
-6B
-7A, -7B
-6B
-7A, -7B
-6B
-7A, -7B
65
55
230
200
230
200
320
300
65
55
250
210
250
210
320
300
65
55
270
230
270
230
320
300
CKE ≥ VIH, /CS ≥ VIH
tRAS = tRAS (max.)
CKE ≥ VIH, BL = 2,
CL = 2.5
CKE ≥ VIH, BL = 2,
CL = 2.5
tRFC = tRFC (min.),
Input ≤ VIL or ≥ VIH
Active standby current
IDD3N
IDD4R
IDD4W
IDD5
3, 5, 6
1, 2, 5, 6
1, 2, 5, 6
Operating current
(Burst read operation)
Operating current
(Burst write operation)
Auto Refresh current
Input ≥ VDD – 0.2 V
Input ≤ 0.2 V
Self refresh current
IDD6
4
3
4
4
Self refresh current
((L-version))
Operating current
(4 banks interleaving)
IDD6
-xxL
3
3
-6B
-7A, -7B
510
430
530
450
490
410
IDD7A
BL = 4
1, 5, 6, 7
Notes: 1. These IDD data are measured under condition that DQ pins are not connected.
2. One bank operation.
3. One bank active.
4. All banks idle.
5. Command/Address transition once per one clock cycle.
6. DQ, DM and DQS transition twice per one clock cycle.
7. 4 banks active. Only one bank is running at tRC = tRC (min.)
8. The IDD data on this table are measured with regard to tCK = tCK (min.) in general.
9. Command/Address transition once every two clock cycles.
10. Command/Address stable at ≥ VIH or ≤ VIL.
DC Characteristics 2 (TA = 0 to +70°C, VDD, VDDQ = 2.5V ± 0.2V, VSS, VSSQ = 0V)
Parameter
Symbol
ILI
min.
–2
max.
2
Unit
µA
Test condition
Notes
Input leakage current
Output leakage current
Output high current
Output low current
VDD ≥ VIN ≥ VSS
VDDQ ≥ VOUT ≥ VSS
VOUT = 1.95V
ILO
–5
5
µA
IOH
IOL
–15.2
15.2
—
—
mA
mA
VOUT = 0.35V
Preliminary Data Sheet E0501E10 (Ver. 1.0)
5