EBE41AE4ABHA
ODT AC Electrical Characteristics (DDR2 SDRAM Component Specification)
Parameter
Symbol
tAOND
tAON
min.
max.
Unit
tCK
ps
Notes
1, 3
ODT turn-on delay
2
2
ODT turn-on
tAC(min)
tAC(max) + 700
2tCK + tAC(max) + 1000
2.5
ODT turn-on (power down mode)
ODT turn-off delay
tAONPD
tAOFD
tAOF
tAC(min) + 2000
ps
2.5
tCK
ps
5
ODT turn-off
tAC(min)
tAC(max) + 600
2, 4, 5
ODT turn-off (power down mode)
ODT to power down entry latency
ODT power down exit latency
tAOFPD
tANPD
tAXPD
tAC(min) + 2000
2.5tCK + tAC(max) + 1000 ps
3
8
3
8
tCK
tCK
Notes: 1. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on.
ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND.
2. ODT turn off time min is when the device starts to turn off ODT resistance.
ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
3. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.)
4. When the device is operated with input clock jitter, this parameter needs to be derated by
{−tJIT(duty) max. − tERR(6-10per) max. } and { −tJIT(duty) min. − tERR(6-10per) min. } of the actual input
clock.(output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10per) min. = −272ps,
tERR(6-10per) max. = +293ps, tJIT(duty) min. = −106ps and tJIT(duty) max. = +94ps, then
tAOF min.(derated) = tAOF min. + { −tJIT(duty) max. − tERR(6-10per) max. } = −450ps + { −94ps − 293ps}
= −837ps and tAOF max.(derated) = tAOF max. + { −tJIT(duty) min. − tERR(6-10per) min. } = 1050ps +
{ 106ps + 272ps} = +1428ps.
5. For tAOFD of DDR2-667, the 1/2 clock of nCK in the 2.5 × nCK assumes a tCH(avg), average input clock
high pulse width of 0.5 relative to tCK(avg). tAOF min. and tAOF max. should each be derated by the
same amount as the actual amount of tCH(avg) offset present at the DRAM input with respect to 0.5. For
example, if an input clock has a worst case tCH(avg) of 0.48, the tAOF min. should be derated by
subtracting 0.02 × tCK(avg) from it, whereas if an input clock has a worst case tCH(avg) of 0.52,
the tAOF max. should be derated by adding 0.02 × tCK(avg) to it. Therefore, we have;
tAOF min.(derated) = tAC min. − [0.5 − Min.(0.5, tCH(avg) min.)] × tCK(avg)
tAOF max.(derated) = tAC max. + 0.6 + [Max.(0.5, tCH(avg) max.) − 0.5] × tCK(avg)
or
tAOF min.(derated) = Min.(tAC min., tAC min. − [0.5 − tCH(avg) min.] × tCK(avg))
tAOF max.(derated) = 0.6 + Max.(tAC max., tAC max. + [tCH(avg) max. − 0.5] × tCK(avg))
where tCH(avg) min. and tCH(avg) max. are the minimum and maximum of tCH(avg) actually measured
at the DRAM input balls.
Data Sheet E0901E20 (Ver. 2.0)
19
ELPIDA [ ELPIDA MEMORY ]
