欢迎访问ic37.com |
会员登录 免费注册
发布采购

KP1J220MR 参数 Datasheet PDF下载

KP1J220MR图片预览
型号: KP1J220MR
PDF下载: 下载PDF文件 查看货源
内容描述: 芯片类型,非偏振光具有较宽的温度范围 [CHIP TYPE, NON-POLARIZED WITH WIDE TEMPERATURE RANGE]
分类和应用:
文件页数/大小: 13 页 / 508 K
品牌: DBLECTRO [ DB LECTRO INC ]
 浏览型号KP1J220MR的Datasheet PDF文件第3页浏览型号KP1J220MR的Datasheet PDF文件第4页浏览型号KP1J220MR的Datasheet PDF文件第5页浏览型号KP1J220MR的Datasheet PDF文件第6页浏览型号KP1J220MR的Datasheet PDF文件第8页浏览型号KP1J220MR的Datasheet PDF文件第9页浏览型号KP1J220MR的Datasheet PDF文件第10页浏览型号KP1J220MR的Datasheet PDF文件第11页  
GENERAL INFORMATION FOR APPLICATION  
The following precautions must be observed when using electrolytic capacitors.  
1. Circuit Design  
1) Please make sure that the environmental and mounting conditions to which the capacitor to be  
exposed are within the conditions specified in this catalogue.  
2) Operating temperature and applied ripple must be within the specifications.  
3) Appropriate capacitors, which comply with the life requirement of the products, should be selected  
when designing the circuit.  
4) Aluminum electrolytic capacitors are polarized. Do not apply reserve voltage or AC voltage. Please  
use non-polarized capacitors for a circuit that can possibly see reserved polarity.  
Note: Non-polarizes capacitors cannot be used for AC voltage application.  
5) Do not use aluminum electrolytic capacitors in a circuit that requires rapid and very frequent charge  
or discharge. In this type of circuit, it is necessary to use special design capacitors with extended life  
characteristics.  
6) Do not apply excess voltage.  
M Pleased pay attention so that the peak voltage, which is DC voltage overlapped by ripple current,  
should not exceed the rated voltage.  
N In the case where more than two aluminum electrolytic capacitors are used in series, please  
make sure that applied voltage should be lower than rated voltage should be applied to each  
capacitor equally using a balancing resistor in parallel with the capacitor.  
7) Outer sleeved of the capacitor is not guarantee as an electrical insulator. Do not use standard sleeve  
on a capacitor in applications that require electrical insulation. When the application requires special  
insulation, please contact our sales office for details.  
8) Capacitors must not be used under following conditions:  
M (a) Capacitors must not be exposed to water (including condensation), brine or oil.  
(b) Ambient conditions that include toxic gases such as hydrogen sulfide, sulfurous acid, nitrous  
acid, chlorine, ammonium, etc.  
(c) Ambient conditions that expose the capacitor to ozone, ultraviolet ray and radiation.  
N Severe vibration and physical shock conditions that exceed our specification.  
Vibration test condition:  
Vibration frequency range: 10~55~10Hz  
Sweet rate  
Sweet method  
: 10~55~10Hz per minute  
: logarithmic  
Amplitude or acceleration: 1.5 (max. acceleration is 10G)  
Direction of vibration  
Testing time  
: X, Y, Z direction  
: 2 hours per each direction  
Shock is not applicable normally.  
If a particular condition is required, please contact our sales office.  
DB LECTRO Inc. 3755 Place Java, Suite 140, Brossard, Québec, J4Y 0E4, Canada - T: 1-450-444-1424 / F: 1-450-444-4714 / www.dblectro.com