欢迎访问ic37.com |
会员登录 免费注册
发布采购

CY7C68013A-56LTXCT 参数 Datasheet PDF下载

CY7C68013A-56LTXCT图片预览
型号: CY7C68013A-56LTXCT
PDF下载: 下载PDF文件 查看货源
内容描述: EZ- USB FX2LP USB微控制器,高速USB外设控制器 [EZ-USB FX2LP USB Microcontroller High Speed USB Peripheral Controller]
分类和应用: 微控制器
文件页数/大小: 62 页 / 1626 K
品牌: CYPRESS [ CYPRESS SEMICONDUCTOR ]
 浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第1页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第2页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第3页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第5页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第6页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第7页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第8页浏览型号CY7C68013A-56LTXCT的Datasheet PDF文件第9页  
CY7C68013A, CY7C68014A
CY7C68015A, CY7C68016A
Table 1. Special Function Registers
x
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
8x
IOA
SP
DPL0
DPH0
DPL1
DPH1
DPS
PCON
TCON
TMOD
TL0
TL1
TH0
TH1
CKCON
9x
IOB
EXIF
MPAGE
Ax
IOC
INT2CLR
INT4CLR
Bx
IOD
IOE
OEA
OEB
OEC
OED
OEE
IP
EP01STAT
GPIFTRIG
GPIFSGLDATH
GPIFSGLDATLX
GPIFSGLDATLNOX
T2CON
RCAP2L
RCAP2H
TL2
TH2
EICON
EIE
EIP
Cx
SCON1
SBUF1
Dx
PSW
Ex
ACC
Fx
B
SCON0
SBUF0
AUTOPTRH1
AUTOPTRL1
reserved
AUTOPTRH2
AUTOPTRL2
reserved
IE
EP2468STAT
EP24FIFOFLGS
EP68FIFOFLGS
AUTOPTRSET-UP
3.5 USB Boot Methods
During the power up sequence, internal logic checks the I
2
C port
for the connection of an EEPROM whose first byte is either 0xC0
or 0xC2. If found, it uses the VID/PID/DID values in the EEPROM
in place of the internally stored values (0xC0), or it boot-loads the
EEPROM contents into internal RAM (0xC2). If no EEPROM is
detected, FX2LP enumerates using internally stored descriptors.
The default ID values for FX2LP are VID/PID/DID (0x04B4,
0x8613, 0xAxxx where xxx = Chip revision).
Table 2. Default ID Values for FX2LP
Vendor ID
Product ID
Device release
Default VID/PID/DID
0x04B4 Cypress Semiconductor
0x8613 EZ-USB FX2LP
0xAnnn Depends on chip revision
(nnn = chip revision where first
silicon = 001)
Two control bits in the USBCS (USB Control and Status) register,
control the ReNumeration process: DISCON and RENUM. To
simulate a USB disconnect, the firmware sets DISCON to 1. To
reconnect, the firmware clears DISCON to 0.
Before reconnecting, the firmware sets or clears the RENUM bit
to indicate whether the firmware or the Default USB Device
handles device requests over endpoint zero: if RENUM = 0, the
Default USB Device handles device requests; if RENUM = 1, the
firmware services the requests.
3.7 Bus-Powered Applications
The FX2LP fully supports bus powered designs by enumerating
with less than 100 mA as required by the USB 2.0 specification.
3.8 Interrupt System
3.8.1 INT2 Interrupt Request and Enable Registers
FX2LP implements an autovector feature for INT2 and INT4.
There are 27 INT2 (USB) vectors, and 14 INT4 (FIFO/GPIF)
vectors. See EZ-USB Technical Reference Manual (TRM) for
more details.
3.8.2 USB Interrupt Autovectors
The main USB interrupt is shared by 27 interrupt sources. To
save the code and processing time that is required to identify the
individual USB interrupt source, the FX2LP provides a second
level of interrupt vectoring, called Autovectoring. When a USB
interrupt is asserted, the FX2LP pushes the program counter to
its stack, and then jumps to the address 0x0043 where it expects
to find a “jump” instruction to the USB Interrupt service routine.
3.6 ReNumeration
Because the FX2LP’s configuration is soft, one chip can take on
the identities of multiple distinct USB devices.
When first plugged into USB, the FX2LP enumerates
automatically and downloads firmware and USB descriptor
tables over the USB cable. Next, the FX2LP enumerates again,
this time as a device defined by the downloaded information.
This patented two step process called ReNumeration™ happens
instantly when the device is plugged in, without a hint that the
initial download step has occurred.
Note
2. The I
2
C bus SCL and SDA pins must be pulled up, even if an EEPROM is not connected. Otherwise this detection method does not work properly.
Document #: 38-08032 Rev. *N
Page 4 of 62