Specification
Absolute Maximum Ratings
Exceeding the maximum rating can result in device damage. Operation of the device outside the operating limits is
not implied.
Supply voltage
-0.3 to 7.0V
Input voltage at any pin (ref VSS = 0V)
-0.3 to (VDD + 0.3V)
Sink/source current (supply pins)
(other pins)
+/- 30mA
+/- 20mA
Total device dissipation @ TAMB 25°C
Derating
800mW Max.
10mW/°C
Storage temperature range:
FX613DW/P
-40°C to +85°C (plastic)
Operating Limits ......
Supply Voltage (VDD)
Min.
3.0
Max.
5.5
Unit
V
at 25°C
Operating Temperature ......
-40
+85
°C
All device characteristics are measured under the following conditions unless otherwise specified:
VDD = 3.3V, TOP = -40 to +85 °C. Audio Level 0dB ref: = 775mVrms. Xtal/Clock Frequency = 3.579545MHz
Characteristics
See Note
Min.
Typ.
Max.
Unit
Static Values
Supply Current
Input Logic “1”
Input Logic “0”
Output Logic “1”
-
70.0
0
90.0
-
0.3
1.0
100
30.0
100
10.0
mA
-
-
-
-
% VDD
% VDD
% VDD
% VDD
1
1
Output Logic “0”
Impedances
Chip Select and Serial Clock Input
Signal Input
Level Input
IRQ Output (logic “0”)
Data Output (logic “0”)
(Logic “1”)
10.0
-
50.0
210
-
500
-
-
-
-
MΩ
kΩ
kΩ
Ω
Ω
kΩ
-
-
-
-
-
500
-
2.5
Dynamic Values
On-Chip Xtal Oscillator
RIN
10.0
-
25.0
5.0
-
-
MΩ
kΩ
V/V
MHz
ROUT
230
42.0
11.0
825
-
-
DC Voltage Gain
Bandwidth at Unity Gain
Single Tone Operation
Must-Decode Input Level
Must-Not Decode Input Level
LO Band Frequency Range
HI Band Frequency Range
Frequency Resolution (Table 1)
LO Band
2
2
4
4
-25.2
-
300
900
-
-
-
dB
dB
Hz
Hz
-46.0
660
2150
-
-
-
-
25.0
75.0
-
-
-
-
Hz
Hz
dB
/sec
/sec
/2 secs
HI Band
-
18.0
-
Input Signal/White-Noise Ratio (HI & LO Bands)
Interrupt Rate (LO Band)
3
3
6
19.0
57.0
-
(HI Band)
-
False Decodes Due to Noise
Outband modulation level limits
for correct decode (fIN = 340Hz to 620Hz)
1.0
5
-
-
10.0
%
Notes
1.
2.
Into a high-impedance load (>1.0MΩ).
Must decode signal above -25.2dB; Must Not decode signal below -46.0dB.
If a supply other than 3.3 volts is used, levels will change pro-rata.
Under ‘Pure Tone’ input conditions.
For input frequencies of between 661Hz and 899Hz the FX613 will provide no reliable output.
With an amplitude modulating frequency of between 16.0Hz and 100Hz.
Test noise input = 5.0kHz at 100mVrms
3.
4.
5.
6.
7
CMLMICRO [ CML MICROCIRCUITS ]
