CS4297A
CS4297A
1. CHARACTERISTICS AND SPECIFICATIONS
ANALOG CHARACTERISTICS
Standard test conditions unless otherwise noted: T
ambient
= 25° C,
AVdd = 5.0 V ±5%, DVdd = 3.3 V ±5%; 1 kHz Input Sine wave; Sample Frequency, Fs = 48 kHz; Z
AL
=100 kΩ/
1000 pF load, C
DL
= 18 pF load (Note 1); Measurement bandwidth is 20 Hz - 20 kHz, 18-bit linear coding for ADC
functions, 20-bit linear coding for DAC functions; Mixer registers set for unity gain.
CS4297A-KQZ
Parameter
Symbol Path
(Note 2)
(Note 3)
Full Scale Input Voltage
A-D
Line Inputs
A-D
Mic Inputs
A-D
Mic Inputs
(20 dB internal gain)
Full Scale Output Voltage
Line,Alternate Line, and Mono Outputs
D-A
FR
Frequency Response
(Note 4)
A-A
Analog
Ac = ± 0.25 dB
D-A
DAC
Ac = ± 0.25 dB
A-D
ADC
Ac = ± 0.25 dB
DR
Dynamic Range
A-A
Stereo Analog inputs to LINE_OUT
A-A
Mono Analog inputs to LINE_OUT
D-A
DAC Dynamic Range
A-D
ADC Dynamic Range
DAC SNR (-20 dB FS input w/
SNR
CCIR-RMS filter on output)
D-A
THD+N
Total Harmonic Distortion + Noise
(-3 dB FS input signal):
A-A
Line/Alternate Line Output
D-A
DAC
A-D
ADC
(all inputs except phone/mic)
A-D
ADC
(phone/mic)
Power Supply Rejection Ratio
(1 kHz, 0.5 V
RMS
w/ 5 V DC offset)(Note 4)
Interchannel Isolation
Spurious Tone
Input Impedance
External Load Impedance
Output Impedance
Input Capacitance
Vrefout
(Note 4)
(Note 4)
(Note 4)
(Note 4)
Min
Typ
Max
Min
CS4297A-JQZ
Typ
Max
Unit
0.91 1.00
0.91 1.00
0.091 0.10
0.91
20
20
20
90
85
85
85
-
1.0
-
-
-
95
90
90
90
70
-
-
-
1.13
20,000
20,000
20,000
-
-
-
-
-
0.91 1.00
0.91 1.00
0.091 0.10
0.91
20
20
20
-
-
-
-
-
1.0
-
-
-
90
85
87
85
-
-
-
-
1.13
20,000
20,000
20,000
-
-
-
-
-
V
RMS
V
RMS
V
RMS
V
RMS
Hz
Hz
Hz
dB FS A
dB FS A
dB FS A
dB FS A
dB
-
-
-
-
40
70
-
10
10
-
-
2.0
-90
-91
-88
-84
60
88
-100
-
-
730
5
2.28
-80
-80
-80
-74
-
-
-
-
-
-
-
2.5
-
-
-
-
-
-
-
10
10
-
-
2.0
-
-
-
-
40
88
-100
-
-
730
5
2.28
-74
-74
-74
-74
-
-
-
-
-
-
-
2.5
dB FS
dB FS
dB FS
dB FS
dB
dB
dB FS
kΩ
kΩ
Ω
pF
V
Notes: 1. Z
AL
refers to the analog output pin loading and C
DL
refers to the digital output pin loading.
2. Parameter definitions are given in the Section 10,
3. Path refers to the signal path used to generate this data. These paths are defined in the Section 10,
4. This specification is guaranteed by silicon characterization, it is not production tested.
DS318PP6
5
5